Precision Digital PD6400 User Manual
Pd6400 high voltage and current meter, Instruction manual
PRECISION DIGITAL CORPORATION
89 October Hill Road • Holliston MA 01746 USA
Tel (800) 343-1001 • Fax (508) 655-8990
www.predig.com
PD6400 High Voltage
and Current Meter
Instruction Manual
• (1) High Voltage and (1) High Current Input
• Multiplication for Apparent Power Calculation
• 0-300 VAC or VDC Voltage Input
• 0-5 AAC or ADC Current Input
• NEMA 4X, IP65 Front
• 85-265 VAC or 12/24 VDC Input Power Models
• Large Dual-Line 6-Digit Display, 0.60" & 0.46"
• Sunlight Readable SunBright Display Models
• Programmable Display & Function Keys
• 2 or 4 Relays + Isolated 4-20 mA Output Options
• External 4-Relay & Digital I/O Expansion Modules
• USB, RS-232 & RS-485 Serial Communication Options
• Modbus
®
RTU Communication Protocol Standard
• Configure, Monitor, and Datalog from a PC with
Free MeterView
®
Pro Software
Document Outline
- INTRODUCTION
- ORDERING INFORMATION
- SPECIFICATIONS
- COMPLIANCE INFORMATION
- safety information
- INSTALLATION
- MOUNTING DIMENSIONS
- Configuration for 12 or 24 VDC Power Option
- Connections
- Connectors Labeling
- Power Connections
- Signal Connections
- Modbus RTU Serial Communications
- Relay Connections
- Switching Inductive Loads
- F4 Digital Input Connections
- 4-20 mA Output Connections
- Analog Output Transmitter Power Supply
- External Relay, Analog Output, & Digital I/O Connections
- Interlock Relay Feature
- SETUP AND PROGRAMMING
- Front Panel Buttons and Status LED Indicators
- Display Functions & Messages
- Main Menu
- Setting Numeric Values
- Setting Up the Meter (setup)
- Setting the Decimal Point (dEc pt)
- Setting the Input Calibration (InCal)
- Multi-Point Linearization (Linear)
- MeterView® Pro Software
- Scaling the Meter without a Signal Source
- Scaling the Meter for Channel A (SCal-A)
- Scaling the Meter for Channel V (SCal-v)
- Error Message (Error)
- Calibrating the Meter with External Source
- Calibrating the Meter for Channel A (CAL-A)
- Calibrating the Meter for Channel V (CAL-v)
- Setting the Display Parameter & Intensity (dsplay)
- Display Setup Menu
- Setting the Input Units or Custom Tags (units)
- Setting the Relay Operation (relay)
- Relay and Alarm Operation Diagrams
- Relay Operation Details
- Overview
- Relays Auto Initialization
- Fail-Safe Operation
- Front Panel LEDs
- Latching and Non-Latching Relay Operation
- Non-Latching Relay (Auto)
- Non-Latching Relay (A-man)
- Latching Relay (LatcH)
- Latching Relay (Lt-Clr)
- Acknowledging Relays
- Pump Alternation Control Applications (Altern)
- Setting Up the Interlock Relay (Force On) Feature
- Scaling the 4-20 mA Analog Output (Aout)
- Reset Menu (reset)
- Control Menu (Contrl)
- Setting Up the Password (pass)
- Advanced Features Menu
- Advanced Features Menu & Display Messages
- Noise Filter (filter)
- Noise Filter Bypass (bypass)
- Rounding Feature (round)
- Modbus RTU Serial Communications (serial)
- Select Menu (SElect)
- Multi-Point Linearization (Linear)
- Math Function (math)
- Math Constants (Const)
- Low-Flow Cutoff (CutofF)
- Analog Output Programming (AoutPr)
- Programmable Function Keys User Menu (user)
- Internal Calibration (ICAL)
- Meter Copy Function (Copy)
- Pump Alternation Control Operation
- Did you forget the password?
- METER OPERATION
- TROUBLESHOOTING