Document Outline

• Title page
• Publication history
• Contents
• About this guide
  • References
• Chapter 1: Meridian Link/CCR co-residency
  • Co-residency overview
  • Keycode
  • Ethernet LAN-based PC
• Chapter 2: Overview of Meridian Link
  • Meridian Link application
  • New with Meridian Link Release 5C
  • Link overview
  • Diagnostic tools
  • Meridian 1
  • Host
  • Meridian Mail software requirements
  • Operations, Administration, and Maintenance (OA&M)
• Chapter 3: Overview of Customer Controlled Routing
  • CCR application
  • New with CCR Release 3C
  • Application Module Link
  • Diagnostic tools
  • Consoles/printers
  • Meridian 1
• Chapter 4: Meridian Link/CCR hardware
  • IPE Module
  • IPE Module Options 21-81
  • Application Module
• Chapter 5: Hardware installation overview
  • Preparing for installation
  • Installing an IPE Module or an Application Module
• Chapter 6: Site survey/installation checklist
  • General information
  • Delivery information
  • Meridian 1 software checklists
  • Meridian Mail hardware checklist to support Meridian Link
  • IPE Module and Application Module: Meridian Link/CCR software
  • Hardware
  • Equipment room information
  • Power and ground considerations
  • Equipment cabling
  • Equipment room cooling conditions
  • Additional considerations
  • Comments and recommendations
• Chapter 7: Unpack and inspect hardware
  • Receiving the IPE Module and Application Module components
  • Unpacking the IPE Module and Application Module components
• Chapter 8: Hardware installation procedures
  • Installing the IPE Module
  • Installing the Application Module
  • Installing the power supply and disk/tape unit (Application Module)
  • Checking the card option settings (Application Module)
  • Installing an NTAK02 SDI/DCH card
  • Installing an ESDI or MSDL card
• Chapter 9: Meridian Link/CCR interface cabling
  • IPE Module cabling
  • Cabling the Option 11 IPE Module to external equipment
  • Backplane cable rerouting for Options 21-81 CE/PE and IPE backplanes
  • Cabling the Options 21-81 IPE Module to external equipment
  • Application Module cabling
  • Cabling the Application Module to external equipment
  • Installing Ethernet LAN support
• Chapter 10: Installing peripheral devices
  • VT220, VT320, and VT420 terminals
  • Personal computer running Reflection 4+
  • Meridian Terminal Emulator (MTE 8)
  • Dot-matrix printer switch settings
  • LaserJet series II printer switch settings
  • LaserJet series III printer switch settings
  • LaserJet series IV printer switch settings
  • DeskJet and DeskJet 500 printer switch settings
• Chapter 11: Peripheral device cabling interface
  • DCE and DTE connections
  • Using an A/B switchbox to share system consoles
  • Modems
• Chapter 12: Meridian 1 configuration for Meridian Link/CCR
  • Conventional notation
  • Configuration overview
  • Configuring the VSID, HSID, and AML prompts
  • Configure ESDI port (X11 Release 17)
  • Enable ESDI port (X81 phase 7 or X11 Release 17)
  • Configure ESDI or MSDL port (X11 Release 18 or later)
  • Enable ESDI or MSDL port (X11 Release 18 or later)
  • Configure SDI port for conshare (X11 Release 17)
  • Configure SDI port for conshare (X11 Release 18 or later)
  • Enable SDI port
  • Configuring DNIS to use auto-terminating trunks
  • Configuring DNIS to use Incoming Digit Conversion
  • Configure devices for status change host notification
  • Configure ACD DNs
  • Configure Control DNs (CCR)
  • Configuring a Phantom Loop
  • Configuring a Phantom Superloop
  • Creating a Phantom Set
  • Configuring Dual VAS ID
  • Traffic statistics
• Chapter 13: Meridian Mail configuration
  • Meridian Mail call processing
  • Configuring Meridian 1 for Meridian Mail
  • Configuring Meridian Mail for Host Enhanced Voice Processing (HEVP)
• Chapter 14: Software installation, upgrade, and update procedures
• Chapter 15: Link configuration
  • Default configuration
  • Link 0 - Application Module Link
  • Link 1 - X.25 protocol (Meridian Link)
  • Link 1 - TCP/IP host link protocol (Meridian Link)
  • Link 2 - Meridian Mail Link (optional for Meridian Link)
  • Changing your configuration
• Chapter 16: Additional application configuration
• Chapter 17: Hardware upgrade
• Chapter 18: Acceptance testing
  • Meridian Link/CCR
  • Meridian Mail
• Chapter 19: Single Terminal Access
  • Hardware and software requirements
  • Before you begin
  • Setting up STA
• Chapter 20: Ordering
• List of terms
• Index
• Back