Inter-Tel CS-5400 User Manual
Page 59
Administrator Procedures
INTER-TEL
®
CS-5200/5400 ADMINISTRATOR GUIDE, ISSUE 1.1 – August 2005
Trunk Programming
Page 41
Ring-In For Day Or Night Mode: To program the endpoint that will have ring in
for this trunk group for day mode, press
or the
RING-IN DAY
menu button. To
program for night mode, press
or the
RING-IN NIGHT
menu button. When the
display shows ENTER ENDPOINT EXTENSION, enter endpoints into the list one
at a time as described above for Answer Access.
Toll Restriction: To program the toll restrictions for the trunk group, press
or
the
TOLL RESTRICTION
menu button. When the display shows TOLL RESTRIC-
TION OPTION, press the numbers that correspond to the toll restrictions you want
to program, as follows:
1.) COS for day or night mode: To program the toll restriction class of service
for day mode, press
or the
COS DAY
menu button. To program class of
service for night mode, press
or the
COS NIGHT
menu button. The display
shows SET DAY (or NIGHT) COS XX. If this is not the COS you want to
program, scroll to the correct COS by pressing the high end of the Volume
button or the
NEXT
menu button to scroll forward, or press the low end of the
Volume button or the
PREVIOUS
menu button to scroll backward. The default
COS numbers are listed below. For definitions, refer to “Class of Service” on
. COS 01 is not used for trunks. When the correct COS is displayed,
press
or the
ON
menu button to enable the toll restriction. Or, press
or
the
OFF
menu button to disable it. If desired, repeat this step to program addi-
tional COS toll restrictions. Then press
or
ACCEPT
to continue.
2.) Exempt from ARS: To program the Exempt from ARS option, press
or
the
EXEMPT FROM ARS
button. When the display shows EXEMPT FROM
ARS, press
or the
YES
menu button to enable the option. Or, press
or
the NO menu button to disable it. Then press
or
ACCEPT
to continue.
3.) Subject to toll restriction: To program the trunk group Subject to Toll Restric-
tion option, press
or the
SUBJECT TO TOLL
menu button. When the dis-
play shows SUBJECT TO TOLL, press
or the YES menu button to enable
the option. Or, press
or the NO menu button to disable it. Then press
or ACCEPT to continue.
Trunk List: To program the list of trunks for the trunk group, press
or the
TRUNK LIST
menu button. When the display shows ENTER TRUNK EXTEN-
SION, enter trunks into the list as follows:
1.) Enter a trunk extension using one of the methods described on
.
2.) The display shows the extension number and a Yes/No prompt. Press
or
the
YES
menu button, followed by
, to include the trunk in the list. Or,
press
or the
NO
menu button, followed by
, to exclude the trunk from
the list.
3.) When the display returns to ENTER TRUNK EXTENSION, select another
extension number. Or, if finished programming the trunk list, press
or
ACCEPT
to continue.
c.
To exit, press
or
ACCEPT
to move backward through the prompts until you
reach the ENTER DATABASE OPTION prompt.
6.
When finished with all programming, press
while the ENTER DATABASE
OPTION prompt is displayed. This ends the programming session.
COS 02 – Deny Area/Office
COS 06 – Deny Equal Access
COS 03 – Deny Operator
COS 07 – Deny Local Calls
COS 04 – Deny Toll Access
COS 08 – Denied Numbers
COS 05 – Deny International
COS 09 – Allowed Numbers
3
4
5
1
2
1
2
#
3
1
2
#
4
1
2
#
6
1
#
2
#
#
#
#