KORG Speaker System - Manual (Page 106)

102
You can also select “Step No.” by using the
[
][ ] keys, the [VALUE] slider, the [VALUE]
dial, or the popup menu.
9 When you play the keyboard as shown in the illus-
tration, the arpeggiator will begin playing.
Tone 0 corresponds to the pitch of the lowest key of
chord you play on the keyboard. (If “Sort” is
unchecked
, it will correspond to the pitch of the
first note you play.)
0 For steps 01–08, make settings for “Pitch Offset,”
“Gate,” “Velocity,” and “Flam.”
“Pitch Offset”: This offsets the pitch of the arpeggio
note in semitones up or down. You can input the
same tone for each step, and change the “Pitch Off-
set” value for each to create a melody using a single
tone. (
☞ “Melody pattern”)
“Gate”: Specify the length of the arpeggio note for
each step. With a setting of Legato, the note will
continue sounding either until the next note of the
same tone or until the end of the pattern. With a set-
ting of Off, the note will not sound.
“Velocity”: Specify the strength of the note. With a
setting of Key, the note will sound at the strength
with which it was actually played.
The “Gate” and “Velocity” settings you make here
will be valid if the “Gate” and “Velocity” parame-
ters (Program P7: Edit-Arpeggiator, Arpeg. Setup
tab) of the program selected in Program mode are
set to Step. If these parameters have a setting other
than Step, the “Gate” and “Velocity” that were
specified for each individual step will be ignored,
and all notes of the arpeggio will sound according
to the settings in Program P7: Edit-Arpeggiator. Be
sure to verify the settings of the program.
Set the “Gate” and “Velocity” by using the
ARPEGGIATOR [GATE] and [VELOCITY] knobs
to the center position (12 o’clock).
A To change the user arpeggio pattern name, use the
“Rename Arpeggio Pattern” page menu command
(
☞ p.38).
B If you wish to save the edited user arpeggio pat-
tern to internal memory, be sure to Write the user
arpeggio pattern (
☞ p.39).
If you turn off the power without writing, the edited
contents will be lost.
C If you wish to save the state of the program at the
same time, return to Program mode and write the
program (
☞ p.38).
Other examples of creating a user arpeggio pat-
tern
Melody pattern
1 Set “Step No.” to 01, and press the [0] key.
Set “Pitch Offset” to +00.
2 Set “Step No.” to 02, and press the [0] key.
Set “Pitch Offset” to +10.
3 Set “Step No.” to 03, and press the [0] key.
Set “Pitch Offset” to +00.
4 Set “Step No.” to 04, and press the [0] key.
Set “Pitch Offset” to +00.
5 Set “Step No.” to 05, and press the [0] key.
Set “Pitch Offset” to +12.
6 For “Step No.” 06, do not enter a tone.
7 Set “Step No.” to 07, and press the [0] key.
Set “Pitch Offset” to +00.
8 Set “Step No.” to 08, and press the [0] key.
Set “Pitch Offset” to –02.
Chordal pattern
1 Set “Step No.” to 01, and press the [0] key.
2 For “Step No.” 02, do not enter a tone.
3 Set “Step No.” to 03, and press the [1], [2], [3], [4]
keys.
4 Set “Step No.” to 04, and press the [1], [2], [3], [4]
keys.