KORG Speaker System - Manual (Page 111)

107
Basic functions
The insert effects, master effects, and master EQ have
the same structure in all modes, but the routing set-
tings will determine how the oscillators of a program
or the timbres of a combination or track of a song will
be sent to each insert effect or master effect. In the
pages that follow, we will explain how you can make
routing settings and effect settings in each mode.
Effect settings for a program
Routing
1 In Program P8: Edit-Insert Effect, select the Rout-
ing tab.
2 Use “BUS Select (IFX/Indiv.Out Assign) to specify
the bus (insertion effect) to which the output of the
oscillator will be sent.
This specifies the bus (or the insert effect) to which
the oscillator output will be sent.
L/R: The output will not be sent to the insert effects.
After passing through the master EQ, the sound will
be sent to AUDIO OUTPUT (MAIN) L/MONO and
R.
IFX1–5:
The output will be sent to insert effect IFX 1,
2, 3, 4, or 5.
1, 2, 3, 4, 1/2, 3/4:
The output will be sent to AUDIO
OUTPUT (INDIVIDUAL) 1, 2, 3, or 4. It will not be
sent to the insert effects, the master effects, or the
master EQ.
Off:
The output will not be sent to AUDIO OUT-
PUT (MAIN) L/MONO, R, or to (INDIVIDUAL) 1,
2, 3, 4. (After passing through the master effects, it
will be output from AUDIO OUTPUT (MAIN).)
Select this when you wish to connect the output to
the master effects in a series connection at the send
levels specified by “Send 1 (MFX1)” and “Send 2
(MFX2).”
For this example, select IFX1.
3 “OSC MFX Send” specifies the send level from
each oscillator to the master effects.
This can be set only when “BUS Select (IFX/
Indiv.Out Assign)” is either L/R or Off.
If “BUS Select (IFX/Indiv.Out Assign)” is set to
IFX1–5
, the send level to the master effects is set by
“Send 1” and “Send 2” (Insert FX tab) after the sig-
nal passes through the insertion effects.
Insert effects
4 Select the Insert Effect tab.
5 For IFX1–5, select the effect type for each insert
effect.
When you press the popup button, all effects will
be displayed, organized into six categories. Use
the tabs located at the left to select a category, and
select an effect from that category on the LCD
screen.
Effects 000–089 can be selected for IFX1, 2, 3, 4, 5,
and MFX1 and 2. Effects 090–102 are double-size
effects, and require twice the processing area of
other effects. These can be selected for IFX2, IFX3,
and IFX4.
Each time you press the ON/OFF button, the
insertion effect will be switched on/off. A setting
of OFF will be the same as when 000: No Effect is
selected. The input sound will be output without
any change.
You can use the “Copy Insert Effect” page menu
command to copy effect settings from another pro-
gram etc. Also, you can use “Swap Insert Effect” to
exchange (for example) IFX1 and IFX5.
6 Make “Chain” settings.
If the “Chain” check box is checked, the insert effect
will be connected in series. Since the output of the
oscillator is being sent to IFX1 in 2, making settings
as shown in the diagram 4 would connect all five
insertion effects IFX1
→ IFX2 → IFX3 → IFX4 →
IFX5 in series, so that these effects would be
inserted into the output of the oscillator.
7 Make settings for “Pan,” “BUS Sel. (BUS Select),”
“Send 1,” and “Send 2” for the sound after it has
passed through the insert effects.
If the insertion effects are chained, these settings
will apply after the last IFX.
“Pan”:
Set the pan. This is valid only when BUS Sel.
is L/R.
“BUS Sel.” (
BUS Select): Specify the output destina-
tion. Normally you will set this to L/R. If you wish
to send the sound that has passed through the insert
effects to AUDIO OUTPUT (INDIVIDUAL) 1–4,
select 1–4, 1/2, or 3/4.
Routing settings and effect set-
tings
Ef
fects settings