KORG M3 - Manual (Page 218)

Appendices
210
• When using the 002: Stereo Limiter or 005: Stereo
Gate, and the Envelope Source of these effects is set
as either FX Control 1 or FX Control 2, and Trigger
Monitor
is On.
• When using 156: Vocoder, with the Modulator
Source of this effect set to FX Control 1 or FX
Control 2, and the Modulator High Mix set to other
than 0.
If the EXB-RADIAS oscillator output is sent through an
insert effect, and then sent to both the AUX bus and the
FX Control bus, the effect settings described above will
produce a feedback loop, possibly producing a loud
noise. Please use caution. (It is also possible that a DC
component will be output at the maximum level,
producing silence.)
Notes do not stop
In Prog P1: Basic/DT/Ctrls– Key Zone/Scale, select
the Program Basic page, make sure that the Hold check
box is unchecked.
→ p.138, PG p.27
Did you use Tone Adjust to turn Hold on?
→ PG p.22
In Global P2: Controller, make sure that Damper
Polarity
or Foot Switch Polarity is set correctly.
→ PG p.371
Programs and Combinations
Settings for oscillator 2 are not displayed
Make sure that the Oscillator Mode (Prog P1: Basic/
DT/Ctrls) parameter is set to Double.
→ p.51
Program does not sound
Have you loaded the multisample or sample that the
program uses?
RADIAS program does not sound
If the oscillator output of the optional EXB-RADIAS or
the oscillator output after passing through an insert
effect is sent via the AUX bus to the input of the EXB-
RADIAS oscillator or the vocoder, a feedback loop will
be created. If this occurs, the input signal will be
automatically cut internally to prevent a loop from
occurring. Be aware that in this case, there will be no
sound.
A combination does not play correctly after
you load data
In the dialog box when you saved the data, did you
check the items that you wanted to save?
→ p.143
Are the bank/numbers of the programs used by the
combination the same as when the combination was
created?
• If you have switched program banks, you can use
the Change all bank references menu command to
change the program bank for each timbre of a
combination.
→ PG p.383
Can’t write a Program
You can’t write EDS programs into bank INT-F.
Likewise, RADIAS programs of the optional EXB-
RADIAS cannot be written to banks INT-A–E.
With the factory settings, the bank type for USER-A–G
banks are all set to EDS programs, so you won’t be able
to write RADIAS programs.
• The bank type for banks USER-A–G can be changed
to store either RADIAS or EDS programs by using
the Global mode menu command Set Prog User-
Bank Type
. You’ll need to change this setting if you
want to write RADIAS programs. → PG p.382
Is the Memory Protect Program checkbox (Global
P0) cleared?
→ p.130
Songs
Song does not play correctly after being
loaded
In the dialog box when you saved the data, did you
check all of the items that you wanted to save?
→ p.143
Are the programs used by the song the same as when
the song was created?
• If you have switched program banks, you can use
the menu command Change all bank references to
change the program bank for each track of a song.
→ PG p.383
• When saving the song, it is best to use Save All or
Save PCG & SEQ so that the programs are saved
together with the song. Then when loading, load
both the .PCG and the .SEQ data.
→ p.143
Have you loaded the multisamples and samples used
by the program?
Playback does not start when you press the
SEQUENCER START/STOP switch in Sequenc-
er mode
Is the MIDI Clock (Global P1: MIDI) set to Internal or
Auto?
→ PG p.364
Can’t record in Sequencer mode
Did you use Track Select to select the MIDI track that
you want to record?
→ p.85
Is the Memory Protect Song check box (Global P0)
unchecked?
→ p.130
Is the MIDI Clock (Global P1: MIDI) set to Internal or
Auto?
→ PG p.364
RADIAS programs of the optional EXB-RADI-
AS don’t sound correctly in a song
Is the optional EXB-RADIAS correctly installed in the
M3?
Is the [R] symbol shown for the track to which the
RADIAS program is assigned?
• Turn Enable RADIAS (Seq P2: EQ/Option) on
(checked).