KORG M3 - Manual (Page 228)

Appendices
220
Not enough song locations available
Meaning: When loading a .SNG file with “Append”
specified, you attempted to load more songs than can
be loaded.
• In Sequencer mode, execute “Delete Song” to
increase the number of multi’s that can be used,
and then load the song again.
Not enough song memory
Meaning: When executing the Sampling mode “Time
Slice” or “Save” commands, the total data for all songs
occupies all of the sequence data memory area, so that
saving is not possible.
Meaning: When sampling to RAM in Sequencer mode,
it is not possible to create track data at the same time.
• Increase the amount of free memory, for example
by deleting another song.
Now switching system clock source... please wait!
Meaning: If the EXB-RADIAS is installed, this message
will appear when you switch the Global mode P0:
Basic Setup– System Preference System Clock setting
to S/P DIF. Please wait until the switch is completed.
O (Obey copyright rules–Oscillator)
Obey Copyright Rules
Meaning: When you execute the Media mode Make
Audio CD Write to CD menu command, or when you
execute Destination in the Sampling mode Audio CD
page Destination menu command.
Please read “COPYRIGHT WARNING” on page iii
before you use this data.
Oscillator Mode conflicts (Check PROG P1)
Meaning: In Sampling mode when you executed
Convert MS To Program with Use Destination
Program Parameters checked, the conversion
destination program Oscillator Mode setting did not
match.
• In Program mode, set the Oscillator Mode of the
conversion destination program. If converting a
monaural multisample, select Single. If converting a
stereo multisample, select Double.
P (Pattern–Program)
Pattern conflicts with events
Meaning: It was not possible to execute the Bounce
operation because one of the tracks contained a
pattern, and the same measure of the other track
contained events or a pattern.
• Open the pattern.
Pattern exists across destination to-end-of-
measure or source from-measure
Meaning: When moving a measure, the edit operation
could not be executed because a pattern had been put
in the destination end measure or the source start
measure, and had not been opened.
• Open the pattern.
Pattern exists in destination or source track
Open pattern?
Meaning: A pattern has been placed in the track that
you specified as a destination or source for editing. If
you wish to open the pattern and execute (the events of
the pattern will be copied), press the OK button. If you
wish to execute without opening the pattern, press the
Cancel button.
Pattern used in song Continue ?
Meaning: When editing, the specified pattern has been
placed in a track. If you wish to execute, press the OK
button. If you decide not to execute, press the Cancel
button.
Program Type conflicts
Meaning: This message will appear when you execute
Copy Tone Adjust if the copy-source and copy-
destination program types are different. You can’t copy
between EDS- and RADIAS-type programs.
R (Rear sample–Root)
Rear sample is empty
Meaning: When you executed Link in the Sampling
mode Sample Edit page, the sample that you specified
as the rear sample is empty.
• Specify a sample that contains data as the rear
sample, and execute once again.
Root directory is full
Meaning: You attempted to create a file or directory in
the root directory of the media, but this would exceed
the maximum number of root directory entries.
• Either delete an existing file or directory, or Open a
directory to move down one level before executing
once again.
S (Sample–S/P DIF)
Sample data used in other sample(s) Continue?
Meaning: Other sample(s) use the same sample data as
the sample that you are editing. To continue editing,
press the OK button.
Sample L and R are identical
Meaning: The edit operation could not be executed
because the destination (save location) L and R sample
numbers are identical.
• Select different sample numbers for L and R of the
destination (save location).
Sample length is shorter than minimum
Meaning: You attempted to execute an editing
operation that would make the sample data shorter
than 8 samples.
• Change the editing range so that the sample data
will be longer than 8 samples.
Sample used in other multisample(s) Continue?
Meaning: The sample you are editing is used by other
multisamples. To continue editing, press the OK
button.