KORG M3 - Manual (Page 226)

Appendices
218
Index number over limit
Meaning: When sampling into RAM in Combination,
Program, or Sequencer mode, there are too many
indexes to be simultaneously converted into a
multisample.
• Either convert the samples into a different program
or multisample, or use Sampling mode to delete
some of the indexes before you continue sampling.
M (Master–Multisample)
Master Track can’t be recorded alone
Meaning: When realtime-recording a single track, you
attempted to begin recording with the master track as
the current track.
• Select a MIDI for recording, instead of the Master
Track.
Measure number over limit
Meaning: The attempted edit operation would cause
the track length to exceed 999 measures.
• Delete unnecessary measures.
Measure size over limit
Meaning: When loading a Standard MIDI File, the
number of events in a measure exceeded the maximum
(approximately 65,535 events).
Meaning: The attempted edit operation would cause
the maximum number of events in a measure
(approximately 65,535) to be exceeded.
To solve either of these problems:
• Use event editing etc. to delete unwanted data.
Medium changed
Meaning: When executing the Copy command in the
Media mode Utility page, the media was exchanged or
ejected, and it was not possible to copy between
separate media on the same drive.
Medium unavailable
Meaning: You selected a medium that does not allow
writing.
Medium write protected
Meaning: The other writing-destination media is
write-protected.
• Turn off write protect on the other media, and
execute the command once again.
Memory full
Meaning: In Sequencer mode when editing a song,
track or pattern, the total data of all songs has used up
all of the sequence data memory, and further editing is
not possible. To solve this problem:
• Delete other song data etc. to increase the amount
of free memory.
Meaning: While realtime recording in Sequencer
mode, there is no more free memory to accommodate
the recorded data, so recording has been forcibly
halted. To solve this problem:
• Delete other song data etc. to increase the amount
of free memory.
Memory overflow
Meaning: While receiving exclusive data in Media
mode Save Exclusive, all remaining internal memory
was used up. To solve this problem:
• If you are receiving two or more sets of exclusive
data, transmit them separately to the M3.
Meaning: In Media mode, you attempted to load more
sample waveform data than there was free memory
capacity. To solve this problem:
• In Sampling mode, execute Delete sample to create
free space in the sample waveform data area, and
re-load the data.
Memory Protected
Meaning: The internal program, combination, song,
drum kit, wave sequence, KARMA GE is protected.
Meaning: The song was protected when you executed
Auto Song Setup.
• In Global mode, turn off write-protect, and execute
the write or load operation once again.
MIDI data receiving error
Meaning: While receiving MIDI System Exclusive
data, the format of the received data was invalid, for
example because the size of the data was incorrect.
Multisample L and R are identical
Meaning: Since the destination (save location) L and R
multisample numbers are the same, the editing
operation could not be executed. To solve this problem:
• Select a different multisample number for the L and
R of the destination (save location).
N (No 48kHz Clock–Now switching
system clock source)
No 48kHz Clock is detected from S/P DIF clock
master device.
The System Clock cannot be changed to S/P DIF.
Meaning: If the EXB-RADIAS is installed, the Global
mode P0: Basic Setup– System Preference System
Clock
cannot be switched to S/P DIF unless a 48 kHz
system clock is being input.
• Please input a 48 kHz system clock from your S/P
DIF Optical format compatible device into the M3’s
S/P DIF IN jack. Only 48 kHz is supported. After
this is input, you’ll be able to switch System Clock
to S/P DIF.
No data
Meaning: When loading a Standard MIDI File, the file
contained no events.
Meaning: When you executed Samples in One
Multisample in Export Smpl as AIFF/WAVE command
in the Media mode Save page, there were no samples.
To solve either of these problems:
• Create sample data.