KORG M3 - Manual (Page 223)

Error messages Error and confirmation messages
215
Quick Start
Introduction
Setup
Program
Combination
Sequencer
Sampling
Global
Media
Effect
KARMA
Drum Track
Other
Appendices
Error messages
Error and confirmation
messages
A (ADC–Are You Sure)
ADC Overload
Meaning: If the ADC OVERLOAD! indication
appears above the Recording Level bar, the signal is
distorting because of an overload at the AUDIO
INPUT stage. To solve this problem:
• Adjust the MIC/LINE gain select switch, the
LEVEL knob (AUDIO INPUT 1 and 2 only), or the
output level of your external audio source.
Are you sure ?
Meaning: This message asks you to confirm execution.
To execute press the OK button. To cancel, press the
Cancel button.
B (Buffer)
Buffer overrun error occurred
Meaning: When sampling to external USB media, the
processing could not keep up with the sampling. To
solve this problem:
• Execute the Media Utility menu command Check
Medium . Then try the sampling operation again. If
this does not resolve the problem, copy several files
from that media to other media, delete those files,
and then try the sampling operation again.
Note: Sampling may not be possible because of the
media you’re using. Please use the recommended
types of media. (See “Media that can be used with the
M3” on page 223)
Note: If the “Buffer overrun error occurred” error
message appears. the data up to the point the error
occurred has been sampled, but the data at the point
the error occurred may not play back correctly.
Buffer underrun error occurred
Meaning: When playing back a WAVE file from
external USB media, the data could not be read fast
enough for playback processing.
• Copy the file you want to play into another folder,
and then execute the operation again.
Note: Playback may not be possible because of the
media you’re using. Please use the recommended
types of media. (See “Media that can be used with the
M3” on page 223)
C (Can’t calibrate–Completed)
Can’t calibrate
Meaning: Calibration could not be performed
correctly.
• Try again.
Can’t copy/swap double size effect
Meaning: When copying or swapping an insertion
effect, you attempted to place a double-size effect in
IFX5.
• Modify your settings so that a double-size effect is
not moved to IFX5, and execute again.
Can’t load divided PCG file
Meaning: The menu command Load PCG (RAM) and
Samples cannot be performed on a divided PCG file.
Can’t open pattern Continue?
Meaning: When you finished recording, it was not
possible to allocate enough memory to open the
pattern that was Put into the track. (When it must be
opened automatically.) If you press the OK button, the
pattern data will be deleted, and the recorded or edited
content will be saved. If you press the Cancel button,
the recorded content will be discarded.
CLIP !
Meaning: The “CLIP !” indication will appear if the
signal level exceeds 0 dB.
• The signal being sampled has overloaded; use the
Recording Level slider to adjust the level.
Note: When inputting from the AUDIO INPUT 1, 2
jacks, you will obtain the widest possible dynamic
range if you adjust the MIC/LINE gain select switch
and the LEVEL knobs as high as possible without
allowing “ADC OVERLOAD!” to appear. In addition,
you should set Level (0–2a) to 127, and adjust
Recording Level
as high as possible without allowing
CLIP ! to appear.
Completed
Meaning: Execution of the command ended normally.
Completed. Please turn the power off, and then
on again
Meaning: Execution of Update System Software has
been completed successfully. Restart the system to
complete the update. Turn the power switch off, and
then on again.
D (Destination–Disk)
Destination and source are identical
Meaning: When copying or bouncing, the same song,
track or pattern was selected for both the source and
destination. To solve this problem:
• Select a different song, track, or pattern for the
source and destination.
Destination from-measure within the limits of
source
Meaning: When executing the Move Measure
command for all tracks or within the same track, the
specified destination measure is within the source
range. To solve this problem: