Vitek VT-4060 SR - Manual (Page 7)

ENGLISH
7
Connecting speaker cables
1. Peel off approximately 1/2 of cable insulation
2. Tighten the wire end (#2 below)
3. Open cable terminal by pressing back on tab
4. Insert wire end into terminal
5. Release tab; make sure wire is in terminal securely
Note: To prevent damage to the circuit, care should be taken
to prevent short circuiting from occurring at the positive and
negative poles of the speaker cord.
CONNECTING ANTENNA
Radio signals may be difficult to receive in some buildings and under
certain conditions. The provided antennas will help in their reception.
They are intended for indoor use only.
AM Loop Antenna
The placement of the AM loop antenna should be in a direction that
provides the clearest reception. Keep as far as possible from DVD
receiver, TV set, and speaker and power cords. If reception remains
poor, an outdoor antenna may be necessary.
To connect the AM loop antenna:
Hold down handle, then insert wire end into hole. Search the handle
position for best reception.
FM Indoor Antenna
The FM antenna should be fully extended and in a direction that provides
the clearest signal. Secure the antenna ends in a location where
distortion is a minimum. If reception remains poor, an outdoor antenna
may be necessary.
System setup
MENU OPERATION:
Press [SETUP] key for the screen to show the setup page. In setup
mode, press [SETUP] key again to quit the setup page. Press direction
key to the desired item, and press [ENTER] to confirm.
(1) Some setup items are concerning the present modes. The items in
gray can’t be set up.
(2) The setup is memorized and will be kept after the power has been
turned off.
System Setup
GENERAL SETUP PAGE
TV Display:
4:3 PANSCAN:
When the unit connects to the normal TV set, the widescreen image
shows on the full screen, but some part is cut off.
4:3 LETTERBOX:
When the unit connects to the normal TV set, the widescreen image
shows and black bars appear on the top and bottom of screen.
16:9:
Use this item when the unit is connected with the wide screen TV set.
Wide Squeeze:
Use this item when the unit is connected to the wide screen TV set.
ANGLE MARK:
It will show the ANGLE mark when playing DVD disc with multi angle view
if selection is ON.
OSD LANG:
Select on screen display language.
CLOSED CAPTIONS:
This function doesn’t work when the disc is without captions. If the
caption is OFF, press [SUBTITLE] key on the remote controller to turn the
captions on.
SCREEN SAVER:
If the SCREEN SAVER is set ON and the unit is switched on without a
disc playing for several minutes, a moving picture appears on the screen
and the unit will go to standby mode after 20 minutes. You can press the
[STANDBY] key on the remote controller to activate.
LAST MEMORY:
When this function is ON, the unit can memorize the time elapsed from
the last time you played the disc. When playing next time, it will resume
playing from
D.R.C: The D.R.C can control data record. You can chose
AUTO, ON and OFF in this mode.
AUDIO SETUP PAGE
ANALOG AUDIO SETUP:
DOWNMIX:
LT/RT:
The audio out is Left and Right channel formatting even if the original
sound is 5.1CH format.
STEREO:
The audio out format is stereo even if the original sound is 5.1CH format.
3D SURROUND:
The audio out is virtual surround sounds (only for 5.1CH player).
OFF:
Turn off DOWNMIX function. If playing 5.1CH discs or the unit is
connected with 5.1 channel amplifier, this item should be selected (only
for 5.1CH player).
FRONT, CENTER, REAR and SUB WOOFER SPEAKER: (No this
item in 2CH player)
If your speaker system includes the above speakers, you can set these
items according the real speaker status.
DIALOG:
The DIALOG mode is available, and you can press up and down direction
key to adjust it. (In the DOWNMIX mode, LT/RT or STEREO is selected).
D.R.C:
The D.R.C can control data record. You can chose AUTO, ON and OFF in
this mode.
4060.indd 7 4060.indd 7 23.10.2006 9:25:12 23.10.2006 9:25:12