Kenwood KDC-X8019BT - Manual (Page 39)

English | 39
When Speaker network is set to 3 way
Display Item Range
“X’Over”
“Tweeter” “FC” Tweeter High Pass Filter
1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5 (kHz)
“SLOPE” Tweeter Slope
-6, -12 dB/Oct
“GAIN” Tweeter Gain
0, -1, -2, -3, -4, -5, -6, -7, -8 dB
“PHASE” Tweeter Phase
Reverse (180°)/ Normal (0°)
“Mid HPF” “FC” Mid Range High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE” Mid Range High Pass Slope
-6, -12 dB/Oct
“GAIN” Mid Range Gain
0, -1, -2, -3, -4, -5, -6, -7, -8 dB
“PHASE” Mid Range Phase
Reverse (180°)/ Normal (0°)
“Mid LPF” “FC” Mid Range Low Pass Filter
1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5,
Through (kHz)
“SLOPE” Mid Range Slope
-6, -12 dB/Oct
“GAIN” Mid Range Gain
0, -1, -2, -3, -4, -5, -6, -7, -8 dB
“PHASE” Mid Range Phase
Reverse (180°)/ Normal (0°)
“Woofer” “FC” Woofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
“SLOPE” Woofer Low Pass Slope
-6, -12 dB/Oct
“GAIN” Woofer Gain
0, -1, -2, -3, -4, -5, -6, -7, -8 dB
“PHASE” Woofer Phase
Reverse (180°)/ Normal (0°)
( : Factory setting)
1
Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Pro Setup”
> “X’Over”.
3
Enter Speaker setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Pro Setup”
> “Speaker Setting”.
4
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
5
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
6
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
X’Over Setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section <Speaker Setting> (page 38).
Display Item Range
“X’Over”
“Front” “FC” Front High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE” Front High Pass Slope
-6, -12, -18, -24 dB/Oct
“GAIN” Front Gain
0, -1, -2, -3, -4, -5, -6, -7, -8 dB
“Rear” “FC” Rear High Pass Filter
Through, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 (Hz)
“SLOPE” Rear High Pass Slope
-6, -12, -18, -24 dB/Oct
“GAIN” Rear Gain
0, -1, -2, -3, -4, -5, -6, -7, -8 dB
“SubWoofer” “FC” Subwoofer Low Pass Filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250, Through (Hz)
“SLOPE” Subwoofer Slope
-6, -12, -18, -24 dB/Oct
“GAIN” Subwoofer Gain
0, -1, -2, -3, -4, -5, -6, -7, -8 dB
“PHASE” Subwoofer Phase
Reverse (180°)/ Normal (0°)
“Tweeter” “FC” Tweeter High Pass Filter
1, 1.6, 2.5, 4, 5, 6.3, 8, 10, 12.5 (kHz)
“TW
Volume”
Tweeter Volume
0, -1, -2, -3, -4, -5, -6, -7, -8 dB
( : Factory setting)
Next page 3
B64-4900-00_00_en.indd 39 11/12/28 12:04