Kenwood KDC-X8019BT - Manual (Page 44)

44 | KDC-X8019BT/ KDC-X8019BTL
Bluetooth Setup
Bluetooth Setting
You can select following Bluetooth Setting items.
1
Enter Bluetooth mode
Press the [
] button.
✍ You can also select from “Settings” in Menu List
mode.
2
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings”.
3
Select the Menu item
Turn the [VOL] knob and press it when the
desired item is displayed.
Display Overview
“SMS Inbox” Display the received short message.
Refer to <SMS (Short Message Service)>
(page 49).
“BT Settings”
“Pairing”
“Device Regist.” Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth Device
(Pairing)> (page 45).
“Phone
Selection”
Select a cell-phone connection.
Refer to <Selecting the Bluetooth device You
Wish to Connect> (page 47). “AUDIO
Selection”
“SPCL DVC
Select”
Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth Device
(Pairing)> (page 45).
“Device Delete” Cancel registration of the Bluetooth device.
Refer to <Deleting a Registered Bluetooth
device> (page 47).
“SMS”
“SMS
Download”
Download a short message.
Refer to <Downloading the SMS> (page
49).
“SMS Reply” Select a method to reply to the received SMS.
Refer to <SMS reply setting> (page 50).
“SMS Message” Create an original message.
Refer to <Creating an original message>
(page 51).
“Detailed Setup” Move to detailed item.
“PIN Code Edit” Specify the PIN code required when registering
this unit using the Bluetooth device.
Refer to <Registering PIN Code> (page 46).
“Auto Answer” Answer a call automatically after lapse of the
preset time interval for automatic answer.
“OFF”/ “0s” – “8s” – “99s”
“Auto
Reconnect”
Automatically reconnects the selected
Bluetooth device when radio wave becomes
strong enough, even after it is disconnected.
“ON”/ “OFF”
✍ When this function is turned ON, the Bluetooth device
is reconnected if it has been disconnected by selecting
“Phone Selection”/ “Audio Selection”.
“Bluetooth HF/
Audio”
*
You can specify output speakers for hands-free
voice communication and Bluetooth audio
sound.
“Front”: Outputs audio from the front speakers.
“All”: Outputs audio from the front and rear
speakers.
“Call Beep” You can output a beep from the speaker when
a call comes in.
“ON”: Beep is heard.
“OFF”: Beep is canceled.
“BT F/W Update” Display the version of the firmware of this unit.
“Mic Gain”
Adjust the sensitivity of the microphone for a
telephone call. Adjust the voice of caller. Setting
to “+” increases the voice volume.
“1” – “20” – “30”
“NR Level” Reduce the noises generated by surrounding
environment without changing the microphone
volume. Adjust the voice of caller when it is
not clear. Setting to “+” increases the noise
reduction.
“–1” – “0” – “+1”
“Echo Cancel
Level“
Adjust the level of echo cancellation. Setting to
“+” increases the echo cancel reduction.
“–1” – “0” – “+1”
( : Factory setting)
* This setting cannot be made when the speaker system is
connected in the 3-way mode.
4
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
5
Exit BT Settings mode
Press the [
] button.
4
MENU VOL
¢ 38
B64-4900-00_00_en.indd 44 11/12/28 12:04