Kenwood KDC-X8019BT - Manual (Page 40)

40 | KDC-X8019BT/ KDC-X8019BTL
DSP Setup
Listening Position Fine Adjustments
Adjusting fine tuning of the speaker position
compensation value specified at <Car Type
Selection> (page 38).
Display Item Range
“FRONT” Front speaker 0 – 610 cm
“REAR” Rear speaker 0 – 610 cm
“SW” Subwoofer 0 – 610 cm
( : Factory setting)
When Speaker network is set to 3 way
Display Item Range
“TW” Tweeter speaker 0 – 610 cm
“MID” Mid Range speaker 0 – 610 cm
“WF” Woofer 0 – 610 cm
( : Factory setting)
1 Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2
Enter Audio Control mode
Press the [VOL] knob.
3
Enter Manual position setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Pro Setup”
> “DTA Setting” > “DTA”.
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired value is displayed.
Item Setting overview
“DTA FRONT” / “L” Front Left speaker
“DTA FRONT” / “R” Front Right speaker
“DTA REAR” / “L” Rear Left speaker
“DTA REAR” / “R” Rear Right speaker
“DTA SW / “L” Subwoofer Left
“DTA SW” / “R” Subwoofer Right
When Speaker network is set to 3 way
Item Setting overview
“DTA TW” / “L” Tweeter Left
“DTA TW” / “R” Tweeter Right
“DTA MID” / “L” Mid Range Left
“DTA MID” / “R” Mid Range Right
“DTA WF / “L” Woofer Left
“DTA WF” / “R” Woofer Right
4
Select the speaker you want to set
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Front”, “Rear”, “SubWoofer” or “Tweeter”.
5
Select the setting item to adjust
Turn the [VOL] knob and press it when the
desired item is displayed.
6
Make a setting
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
7
Repeat steps 4 to 6 to complete the X’Over
settings.
8
Exit Audio Control mode
Press the [MENU] button for at least 1 second.
Listening Position Selection
The sound environment can be compensated in
accordance with the selected position. According to
the listening position, select the position from the
following settings.
Display Compensation seat
“ALL” Not compensating.
“Front-Left” Front-Left seat
“Front-Right” Front-Right seat
“Front” Front seat
( : Factory setting)
1
Select the source
Pressing the [SRC] button repeatedly switches
source.
Select a source other than “STANDBY”.
✍ SRC Select mode 2: Press the [SRC] button and
then turn the [VOL] knob. To determine the
selected source, press the [VOL] knob.
2
Enter Audio Control mode
Press the [VOL] knob.
3 Enter Preset position setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Pro Setup”
> “DTA Setting” > “Position”.
4
Select the seat you want to compensate
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
5 Exit Audio Control mode
Press the [MENU] button for at least 1 second.
B64-4900-00_00_en.indd 40 11/12/28 12:04