AC International Lenze SV01B - Manual (Page 8)

ENGLISH
ESV7N04TXB
ESV75N04TXB
ESV2N04TXB
ESV52N04TXB
ESV222N04TXB
ESV402N04TXB
ESV552N04TXB
ESV752N04TXB
ESV75N0TXB
ESV52N0TXB
ESV222N0TXB
ESV402N0TXB
ESV552N0TXB
ESV752N0TXB
The SMVector drive is designed to operate at the Nominal Output Current (I
n
) shown
in the Ratings tables for most standard applications and industrial environments. The
drive output current or operating temperature may need to be limited as described
below:
For combinations of the above, please consult Lenze / AC Tech applications support
for proper derating.
7
Technical data
480VAC Models
Type Power
[Hp/kW]
Mains Output Current
Watts
Loss
Voltage (1) I
in
I
n
CLim
max
(2)
400V 480V 400V 480V 400V 480V
0.5 / 0.7
400 V Three-phase (3/PE)
(40 … 440 V)
OR
480 V Three-phase (3/PE)
(40 … 528 V)
.7 .5 . . 75 200 2
 / 0.75 2.9 2.5 2.4 2. 75 200 7
.5 / . 4.2 . .5 .0 75 200 48
2 / .5 4.7 4. 4.0 .5 75 200 57
 / 2.2 . 5.4 5.5 4.8 75 200 87
5 / 4.0 0. 9. 9.4 8.2 75 200 28
7.5 / 5.5 4.2 2.4 2. .0 75 200 78
0 / 7.5 8. 5.8 . 4.0 75 200 208
600VAC Models
Type Power
[Hp/kW]
Mains Output Current
Watts
Loss
Voltage (1) I
in
I
n
CLim
max
(2)
 / 0.75
600 V Three-phase (3/PE)
(425 … 0 V)
2.0 .7 200 37
2 / .5 .2 2.7 200 5
 / 2.2 4.4 .9 200 8
5 / 4.0 .8 . 200 0
7.5 / 5.5 0.2 9 200 48
0 / 7.5 2.4  200 72
() Frequency Range: 48 Hz … 2 Hz
(2) Current Limit (CLim) is a percentage of the output current, I
n
. CLim
max
is the maximum setting for P7.
For 480VAC models, the CLim
max
value in the 480V column of the table is used when P07 is set to .
The CLim
max
value in the 400V column is used when P07 is set to 0.
STOP!
Drive Derating
• For installations above 000m a.m.s.l., derate I
n
by 5% per 000m, do not exceed
4000m a.m.s.l.
• Operation above 40°C, derate I
n
by 2.5% per °C, do not exceed 55°C.
• Carrier Frequency (P):
- If P=2 (8 kHz), derate I
n
to 92% of drive rating or do not exceed °C ambient
- If P= (0 kHz), derate I
n
to 84% of drive rating or do not exceed 27°C ambient