Document Outline

• EH7510 Industrial Managed Ethernet Switch User Manual
  • Important Announcement
  • Table of Contents
  • Preface
  • Chapter 1: Introduction
    • 1.1 What is a Managed Industrial Switch
    • 1.2 Software Features
    • 1.3 Hardware Features
    • 1.4 Power Requirements
    • 1.5 Environmental Limitations
    • 1.6 LED Indicators
  • Chapter 2: Configuring with a Web Browser
    • 2.1 Web-based Management Basics
      • 2.1.1 Default Settings
      • 2.1.2 Login Process and Main Window Interface
    • 2.2 Information
      • 2.2.1 Basic
      • 2.2.2 Console
      • 2.2.3 Power Status
      • 2.2.4 Protocol Status
    • 2.3 Administration
      • 2.3.1 System Settings
      • 2.3.2 Password
      • 2.3.3 IP Settings
      • 2.3.4 Forwarding and QoS
        • 2.3.4.1 CoS Mapping
        • 2.3.4.2 ToS/DiffServ Mapping
      • 2.3.5 Mirror Port
      • 2.3.6 System Time and SNTP
      • 2.3.7 Modbus Setting
      • 2.3.8 PTP Setting
    • 2.4 Port
      • 2.4.1 Port Status
      • 2.4.2 Port Statistics
      • 2.4.3 Port Control
    • 2.5 Trunking
      • 2.5.1 LACP
      • 2.5.2 Trunking
    • 2.6 Unicast/Multicast MAC
      • 2.6.1 MAC Address Table
      • 2.6.2 Add Uni/Multicast MAC
      • 2.6.3 Filter MAC
    • 2.7 GARP/GVRP/GMRP
      • 2.7.1 Multicast Group Table
      • 2.7.2 GARP
      • 2.7.3 GVRP
      • 2.7.4 GMRP
    • 2.8 IGMP/IP Multicast
      • 2.8.1 IGMP/IP Multicast Table
      • 2.8.2 Static IP Multicast
      • 2.8.3 IGMP
      • 2.8.4 IGMP Statistics
    • 2.9 SNMP
      • 2.9.1 Community Strings
      • 2.9.2 Trap Receivers
      • 2.9.3 SNMPv3 Users
    • 2.10 Spanning Tree
      • 2.10.1 Spanning Tree
      • 2.10.2 Spanning Tree Port
    • 2.11 VLAN
      • 2.11.1 VLAN Mode
      • 2.11.2 VLAN TABLE
      • 2.11.3 VLAN Setting
      • 2.11.4 VLAN PVID
      • 2.11.5 Example of using 802.1Q VLAN
    • 2.12 Port Security
      • 2.12.1 Static Port Security
      • 2.12.2 Add Static MAC
      • 2.12.3 802.1x and Radius
      • 2.12.4 802.1.x
      • 2.12.5 802.1x Port
    • 2.13 ERPS/Ring
      • 2.13.1 DIP Switch
      • 2.13.2 ERPS
        • 2.13.2.1 UERPS Settings (optional)
      • 2.13.3 iA-Ring
      • 2.13.4 Compatible-Ring
      • 2.13.5 U-Ring
    • 2.14 LLDP
      • 2.14.1 LLDP
      • 2.14.2 Neighbors
    • 2.15 System Warning
      • 2.15.1 Warning Event Selection
      • 2.15.2 Alert Warning Events
      • 2.15.3 SMTP Settings
    • 2.16 Diagnosis
      • 2.16.1 Ping
    • 2.17 System Log
      • 2.17.1 Syslog
      • 2.17.2 Event Log
    • 2.18 System
      • 2.18.1 Backup/Restore
      • 2.18.2 Firmware Upgrade
      • 2.18.3 TFTP
      • 2.18.4 Factory Default
      • 2.18.5 Reboot
  • Chapter 3: Configuring with a Serial Console
    • 3.1 Serial Console Setup
    • 3.2 Command Line Interface Introduction
    • 3.3 General Command
    • 3.4 Command Example
      • 3.4.1 Administration Setup using Serial Console
      • 3.4.2 Spanning Tree Setup using Serial Console
  • Chapter 4: SwitchView & Topolog Diagram
    • 4.1 SwitchView
    • 4.2 Firmware Upgrade
    • 4.3 Topology Diagram
  • Appendix A. ModBus Management Memory Map
    • System Information
    • Console Information
    • Power Information
    • IP Information
    • System Status Clear
    • Warning Events Information
    • Port Status
    • Redundancy Information
  • Glossary