Banner D10 Series - Manual (Page 2)

D10 Expert
™
Dual Discrete Outputs
2
P/N 64154 rev. F
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Figure 1. D10 features
dynamic
static
Output
Indicators
Output Select
Indicators
4-Digit
Display
Light/Dark
Operate, Clock
and Lock Icons
Programming
Push Buttons
For emitter and receiver port
locations, see page xx.
Overview
The D10 Expert Sensor is a high-performance plastic fiber-optic sensor whose many
configuration (TEACH-mode) options make it suitable for demanding applications. Even with
all its features, it is extremely easy to use. Advanced 16-bit microcontroller technology makes
this possible.
The D10 Expert provides high-performance sensing in low-contrast applications. Expert
TEACH and setup options provide static, dynamic and single-point programming plus manual
fine adjustment, remote programming and push button lockout. Its slender, stylized housing
has a large digital display visible beneath a clear cover for easy programming and status
monitoring during operation. The sensor mounts directly to standard 35 mm DIN rail or using
the supplied mounting bracket.
The sensor features two outputs with independent setpoints: either NPN or PNP, depending
on model. Built-in crosstalk avoidance protocol provides trouble-free operation for multiple
sensors in one area.
Light/Dark
Operate Selection
Toggle to select the condition for which each output will conduct: when the target is present or when the target is absent.
OFF-Delay Timing
Selection
Programmable OFF-delay pulse stretcher: 0, 2, 5, 10, 15, 20, 30, 40, 60, 80, or 100 milliseconds
Display Selection Discrete Output: Raw signal value or % excess signal
Power Level/
Speed Selection
Super High-Speed† (SHS) High-Speed (HS) High-Power (HP) Super High-Power (SHP)
Response* 50 µs 200 µs 1 ms 2.5 ms
Repeatability 25 µs 50 µs 75 µs 100 µs
Maximum
Range*
Fiber Red 680 nm Green 525 nm Red 680 nm Green 525 nm Red 680 nm Green 525 nm Red 680 nm Green 525 nm
PIT16U 20 mm 9 mm 30 mm 9 mm 55 mm 13 mm 90 mm 16 mm
PIT26U 100 mm 40 mm 150 mm 40 mm 250 mm 55 mm 400 mm 70 mm
PIT46U 300 mm 100 mm 550 mm 100 mm 1000 mm 160 mm 1200 mm 180 mm
PIT66U 600 mm 180 mm 1000 mm 180 mm 1700 mm 280 mm 2400 mm 320 mm
PBT16U 6 mm ** 10 mm ** 18 mm 3 mm 30 mm 3.5 mm
PBT26U 30 mm 12 mm 50 mm 12 mm 100 mm 20 mm 150 mm 25 mm
PBT46U 100 mm 30 mm 175 mm 30 mm 250 mm 42 mm 300 mm 60 mm
PBT66U 175 mm 55 mm 250 mm 55 mm 400 mm 80 mm 475 mm 100 mm
Tracking Feature Sets Output 2 to identical settings as Output 1; Output 2 settings can then be revised as desired. (See Advanced Setup procedure, page 11.)
Factory Default
Settings The following settings are preset at the factory; revert sensor to factory defaults using Advanced Setup procedure (page 11).
• Light operate (LO)
• Output 1 displayed • Maximum power setting
• No OFF-delay (t 0) • High Speed (HS); 200 µs response • Discrete: switchpoint positioned at middle of range
• Raw signal value (1234)
* Diffuse mode performance based on 90% reflectance white test card.
** ø0.010" bifurcated fiber not recommended in these speed settings. Contact Banner Applications for more information.
† See note on page 10.