EVCO EC6708 - Manual (Page 6)

Every Control S.r.l.
Via Mezzaterra 6, 32036 Sedico Belluno ITALY • Phone 0039-0437-852468 (a.r.) • Fax 0039-0437-83648 • [email protected] • www.everycontrol.it 6
INSTRUMENT DESCRIPTION
Keys - LED - Displays
tion parameter value
5 up key ; it permits
• during the manual power steps loading/unloading procedure,
to load a power step
• during the working setpoint setting procedure, to increase the
working setpoint value
• during the configurator, operator and User Menu configura-
tion parameters setting procedure, to select a configuration
parameter
• during the configurator, operator and User Menu configura-
tion parameters setting procedure, to increase a configura-
tion parameter value
6 set key ; it permits
• during the manual power steps loading/unloading procedure,
to display a power step status
• during the users total working hours counter cleaning proce-
dure, to display a user total working hours
• to display the working setpoint value
• during the configurator, operator and User Menu configura-
tion parameters setting procedure, to display a configuration
parameter value
23 ON STAND-BY key ; it permits
• to turn on the instrument
• to turn off the instrument
• to turn out from the configurator and Operator Menu configu-
ration parameters setting procedure.
LED
7 set LED; it indicates
• if it flashes, that a working setpoint setting procedure or a
configurator or operator or User Menu configuration param-
eter modification procedure is running
8 minutes LED ; it indicates
• if it is turned on, that the unit of measure of the displayed
quantity is the minute
9 hours LED ; it indicates
• if it is turned on, that the unit of measure of the displayed
quantity is the hour
10 bar LED ; it indicates
• if it is turned on, that the unit of measure of the displayed
quantity is the bar or that the displayed quantity is a pressure
11 Celsius degree LED ; it indicates
• if it is turned on, that the unit of measure of the displayed
quantity is the Celsius degree or that the displayed quantity is a
temperature
13 data LED ; it indicates
• if it flashes, that a data transmission in a serial network with
EVCOBUS protocol communication managed by a master (for
instance a Personal Computer) is running
14 alarm LED ; it indicates
• if it flashes, that an alarm is active
15 service LED ; it indicates
• if it is turned on, that an user has exceeded the number of total
working hours enough to signal the request of service
19 compressor/choking valve associated to the output K1 ... 8 LED; it
indicates
• if it is turned on, that the user associated to the output K1 ... 8
is a compressor or a choking valve
• if it flashes, that a count of a disabling time to the compressor
associated to the output K1 ... 8 activation is running
20 condenser fans associated to the output K1 ... 8 LED; it indicates
• if it is turned on, that the user associated to the output K1 ... 8
is a condenser fans
21 power step or condenser fans associated to the output K1 ... 8
status LED; it indicates
• if it is turned on, that the power step associated to the output
K1 ... 8 is loaded or that the condenser fans associated to the
output K1 ... 8 is activated
• if it flashes during an alarm, that the user associated to the
output K1 ... 8 locking digital input is active
22 ON STAND-BY LED; it indicates
• if it is turned on, that the instrument is in the status STAND-BY
26 menu LED; it indicates
• if it is turned on, that a configurator or Operator Menu con-
figuration parameters setting procedure is running.
DISPLAYS
12 display; it permits to display
• during an alarm, the alarm code
• the pressure read by the suction probe
• during the users total working hours counter cleaning proce-
dure, the user total working hours
• during the manual power steps loading/unloading procedure,
the power step status
• during the working setpoint setting procedure, the working