Interlogix Monitor XL Advanced Installation Guide - Manual (Page 58)

52 Monitor xL™ Advanced Installation Guide 21-3602E rev1.5
R00102, 05 Keypad Selections (left to right on keypad screen)
Default Name
Selections Description
000 Reader Class Map
Schedule 00 = Treat as In Schedule
01 – 250 Schedule Enter a schedule for reader-class
restriction.
00 Group Number 00 = none, 1 – 63, Reader Group
Number.

(yes)
In Schedule A 
(yes) □ (no)
Whether Class A users can enter during
schedule

(yes) In Schedule B

(yes) □ (no)
Whether Class B users can enter
during schedule

(yes) In Schedule C

(yes) □ (no)
Whether Class C users can enter
during schedule

(yes) Out of Schedule A

(yes) □ (no)
Whether Class A users can enter
outside of the sched.

(yes) Out of Schedule B

(yes) □ (no)
Whether Class B users can enter
outside of the sched.

(yes) Out of Schedule C

(yes) □ (no)
Whether Class C users can enter
outside of the sched.
 (no) Anti-pass Back 
(yes) □ (no)
Whether cards are to be blocked
against re-entry before exiting first.
 (no) Log APB Violation
Only

(yes) □ (no)
Whether 'Anti-pass Back violators'
will be granted entry.

(yes)
Enable Class
Checking 
(yes) □ (no)
Door class (A,B,C) checking, on or
off.
R00103,06 Keypad Selections
(left to right on keypad screen) Example:
Default Name
Selections Description
000 Card Mode Schedule 00 = Use as In Schedule setting
01 – 250 (Schedule) Enter a schedule to allow cycling
between different 'card' modes during the
daytime, vs. after-hours.
000 Reader Mode
Schedule 00 = Use as In Schedule setting
01 – 250 (Schedule) Enter a schedule to allow cycling
between different reader modes during
the daytime, compared with after-hours.
2 Card Mode In
Schedule 0=Card only,1= Card + PIN, 2= Card or
UID/ PIN,3= UID/ PIN only The basic method that entrants will have
to use to gain entry at this door—i.e., via
access token and/or by keying-in a PIN.
2 Card Mode Out of
Schedule 0=Card only,1= Card + PIN, 2= Card or
UID/ PIN, 3 = UID/ PIN only
Same as ‘Card Mode In Schedule’
0 Reader Mode In
Schedule 0=Normal,1= Dual Custody, 2= Escort,
3= Toggle Lock all user, 4= Toggle lock
authorized. 5–7=Future Sets whether a second user, or initial
escort will be required to gain entry (while
the schedule is active).
0 Reader Mode Out of
Schedule 0=Normal,1= Dual Custody, 2= Escort,
3= Toggle Lock all user, 4= Toggle lock
authorized. 5–7=Future
Sets whether a second user, or initial
escort will be required to gain entry
(outside of the schedule).
(Schedules): Select "00" to have the "During Schedule" selection apply all of the time.
To set up schedules or view related settings, refer to "D001 - (Schedules for Area/Access/Door Automation)".
Card Mode: For "ID/PIN only", an access token is NOT required, and the entrant must enter either their PIN or ID+PIN. For an armed area that is
NOT set to 'Auto Disarm on Valid Token', the user will also have to access the alarm system and disarm the area. For details on ‘Auto Disarm on
Valid Token’, refer to A0xx:04 (Areas and Related Settings)".
Reader Mode: For access to be granted when dual custody is in effect, two users who have the authority to enter the specific door at the present
time must present their card and/or PIN at the reader. With escort mode, the second user must have "Escort" authority. (A valid 'escort' can also
enter on their own by presenting their card/PIN twice.) To assign escort authority to a block of users (i.e., those assigned to a specific authority
level), refer to I00102 (Authority Levels for Users/Entrants)". Tip: "Dual Custody" is also supported referring to disarming an area. For details,
refer to A0xx02 (Areas and Related Settings)".
000 · 000 · 2 · 2 · 0 · 0 ·

Save R001

03