Marantz SR5004 - Manual (Page 47)

NAMES AND FUNCTIONS
45
BASIC
CONNECTIONS
BASIC
OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
ADV
ANCED
OPERA
TION
ENGLISH
ADVANCED OPERATION
TUNER OPERATION
(PRESET MEMORY)
The unit shown in the illustrations is SR6004.
PRESET MEMORY
With this unit you can preset up to 60 FM/AM
stations in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
2. 4. 1. 3. 5. 2.
1.
To select FM , press the BAND button on
the front panel.
2. While pressing the MEMORY button, press
the 2 cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest
frequency.
3. Each time the tuner fi nds a station, scanning
will pause and the station will be played for
fi ve seconds.
During this time, the following operations
are possible.
The band can be changed by the BAND
button.
4.
If no button is pressed during this period,
the current station is memorized in location
Preset 01.
If you wish to skip the current station, press
the 3 cursor button during this period,
this station is skipped and auto presetting
continues.
5. Operation stops automatically when all 60
preset memory positions are fi lled or when
auto scanning attains the highest end of all
bands. If you desire to stop the auto preset
memory at anytime, press the CLEAR
button.
MANUAL PRESET MEMORY
2.
3.
3. 2. 4.
(Using the unit)
1.
Tune into the radio station you desire (Refer
to the “MANUAL TUNING” or “AUTO
TUNING” section).
2.
Press the MEMORY button on the front
panel. “– –“ (preset number) starts blinking
on the display.
3.
Select the preset number by pressing the
1 or 2 cursor buttons, while this is still
blinking (approx. 5 seconds)
4. Press the MEMORY button again to enter.
The display stops blinking.
The station is now stored in the specifi ed
preset memory location.
(Using the remote controller)
1.
Tune into the radio station you desire (Refer
to the “MANUAL TUNING” or “AUTO
TUNING” section).
2.
Press the MEMO button on the remote
controller. “– –“ (preset number) starts
blinking on the display.
3.
Enter the desired preset number by pressing
the numeric buttons.
Note
• When entering a single digit number (2 for
example), either input “02” or just input “2” and
wait for a few seconds.
RECALLING A PRESET STATION
3. 1.
2.
2.
(Using the unit)
1.
Select the desired preset station by pressing
the 1 or 2 cursor buttons on the front
panel.
(Using the remote controller)
1. Press the TUNE button twice within two
seconds on the remote controller.
2. Press the 1 or 2 button to tune in the
deseired preset station.
Or enter the preset station number with the
numeric buttons.
PRESET SCAN
1.
5.
4.
2.
5.
(Using the remote controller)
1.
Press the TUNE button twice within two
seconds on the remote controller.
2.
Press the P.SCAN button on the remote
controller.
“PRESET SCAN” appears on the front
display and then the preset station with the
lowest preset number is recalled fi rst.
3. Preset stations are recalled in sequence
(No.1 → No.2 → etc.) for 10 seconds each.
No stored preset number will be skipped.
4.
You can fast forward the preset stations,
press the 2 continuously.
5.
When the desired preset station is received,
cancel the preset scan operation by pressing
the CLR button or P.SCAN button on the
remote controller.
PRESET CHANNEL LIST DISPLAY
A complete list of the broadcast channels stored in
this unit can be displayed.
1.
2.
4.
1.
Press the TUNE button on the remote
controller twice within two seconds to
switch to the TUNER function.