Verilink PRISM 3101 (34-00212) Product Manual - Manual (Page 43)

SNMP Agent C-3 PRISM 3101/3102
SET: dsx1NoLoop(1) - deactivates any loops active on the unit
dsx1PayloadLoop(2) - the unit will activate a PLB if no
other loops are active
dsx1LineLoop(3) - the unit will activate a LLB if no
other loops are active
dsx1OtherLoop(4) - the unit will activate Port Loops an
any active ports, if no other loops are active
dsx1LineStatus: (read-only)
GET: returns a sum of the following
dsx1NoAlarm(1) - the unit has no alarms
dsx1RcvFarEndLOF(2) - the unit is receiving a Yellow
Alarm from the Far End
dsx1XmtFarEndLOF(4) - unit is transmitting a Yellow
Alarm
dsx1RcvAIS(8) - the unit is receiving AIS from the Far
End
dsx1XmtAIS(16) - not applicable
dsx1LossOfFrame(32) - unit is currently in an OOF con-
dition
dsx1LossOfSignal(64) - the unit is currently in a LOS
condition
dsx1LoopbackState(128) - the unit has a loop active
(PLB, LLB, Port 1, or Port 2)
dsx1T16AIS(256) - not applicable
dsx1RcvFarEndLOMF(512) - not applicable
dsx1XmtFarEndLOMF(1024) - not applicable
dsx1RcvTestCode(2048) - not applicable
dsx1OtherFailure(4096) - not applicable
dsx1SignalMode: (read-write)
GET: none(1) - this signal mode is the only mode supported
robbedBit(2) - not applicable
bitOriented(3) - not applicable
messageOriented(4) - not applicable
SET: none(1) - not applicable
robbedBit(2) - not applicable
bitOriented(3) - not applicable
messageOriented(4) - not applicable
dsx1TransmitClockSource: (read-write)
GET: loopTiming(1) - Network Timing is set to Network Clock
localTiming(2) - the Network Timing is set to Internal
Clock
throughTiming(3) - the Network Timing is set to Port 1
Clock or Port 2 Clock
SET: loopTiming(1) - sets network timing to the network clock
localTiming(2) - sets the network timing to the internal
clock
throughTiming(3) - sets network timing to the Port 1
clock
dsx1Fdl: (read-write)
GET: returns a sum of the following
other(1) - Rem Comm Channel is active
dsx1Ansi-T1-403(2) - the Network Framing is ESF, and
PRM Enable is Enabled
dsx1Att-54016(4) - the Network Framing is ESF or Rem
Comm Channel is active, therefore 54016 messaging is
active
dsx1Fdl-none(8) - the Network Framing is D4, and there
is no active Rem Comm Channel
SET: other(1) - not applicable
dsx1Ansi-T1-403(2) - sets PRM Enable to Enabled
dsx1Att-54016(4) - not applicable
dsx1Fdl-none(8) - sets PRM Enable to Disabled
dsx1CurrentTable
dsx1CurrentIndex: (read-only)
GET: (2) - if a NIC is not installed
(3) - if a NIC is installed
dsx1CurrentESs: (read-only)
GET: returns the number of Errored Seconds (per 54016) in the
current 15 minute interval
dsx1CurrentSESs: (read-only)
GET: returns the number of Severely Errored Seconds (per
TR54016) in the current 15 minute interval
dsx1CurrentSEFSs: (read-only)
GET: returns the number of Loss Of Frame Seconds (per 54016)
in the current 15 minute interval
dsx1CurrentUASs: (read-only)
GET: returns the number of Unavailable Seconds (per 54016) in
the current 15 minute interval
dsx1CurrentCSSs: (read-only)
GET: returns the number of Controlled Slip Seconds (per
54016) in the current 15 minute interval
dsx1CurrentPCVs: (read-only)
GET: returns 0
dsx1CurrentLESs: (read-only)
GET: returns the number of Bipolar Violation Seconds (per
54016) in the current 15 minute interval
dsx1CurrentBESs: (read-only)
GET: returns the number of Bursty Errored Seconds (per 54016)
in the current 15 minute interval
dsx1CurrentDMs: (read-only)
GET: returns 0
dsx1CurrentLCVs: (read-only)
GET: returns 0
dsx1IntervalTable
dsx1IntervalIndex: (read-only)
GET: (2) - if a NIC is not installed
(3) - if a NIC is installed
dsx1IntervalNumber: (read-only)
GET: returns the interval number for the interval requested, a
number from 1 to 96
dsx1IntervalESs: (read-only)
GET: returns the number of Errored Seconds (per 54016) in the
specified 15 minute interval