Yaskawa AC Drive-P1000 Industrial Fan User Manual
Page 562
oFC01 ............................................................................ 303
oFC02 ............................................................................ 303
oFC03 to oFC11 ................................................................ 303
oFC12 to oFC17 ................................................................ 303
oFC50 to oFC55 ................................................................ 303
oH ........................................................................... 303, 315
oH1 ............................................................................... 304
oH2 ............................................................................... 315
oH3 ............................................................................... 315
oH4 ............................................................................... 316
oH5 ............................................................................... 304
oH Alarm Location Monitor .................................................. 463
oL1................................................................................ 304
oL2................................................................................ 305
oL2 Characteristics Selection at Low Speeds......................... 259, 446
oL3................................................................................ 305
oL4................................................................................ 305
oL7................................................................................ 305
oPE ............................................................................... 318
oPE01 ............................................................................ 318
oPE02 ............................................................................ 318
oPE03 ............................................................................ 318
oPE04 ............................................................................ 319
oPE05 ............................................................................ 319
oPE07 ............................................................................ 319
oPE09 ............................................................................ 320
oPE10 ............................................................................ 320
oPE11 ............................................................................ 320
oPE28 ............................................................................ 320
oPE Fault Parameter............................................................ 459
Operating with the Load Connected.......................................... 136
Operation Errors .......................................................... 292, 295
Operation Selection when Digital Operator is Disconnected ....... 270, 450
Operation Status Monitors..................................................... 285
Operator Programming Errors ................................................ 318
Operator Related Settings...................................................... 266
Operator RUN Save at Power Loss .................................... 270, 450
oPr ................................................................................ 305
Optional 24 V DC power supply connector cover .... 36, 37, 38, 39, 40, 41
Option card connection error (CN5-A) ...................................... 302
Option Card Connection Error at Option Port CN5-A..................... 301
Option Card Connection Error at Option Port CN5-C..................... 303
Option card connector (CN5-A) ................................................44
Option card connector (CN5-B) ................................................44
Option card connector (CN5-C) ................................................44
Option card error occurred at option port CN5-A .......................... 302
Option card error occurred at option port CN5-B .......................... 302
Option card error occurred at option port CN5-C .......................... 303
Option Card External Fault.............................................. 298, 313
Option Card Fault at Option Port CN5-A ................................... 302
Option Card Fault at Option Port CN5-B.................................... 302
Option Card Fault at Option Port CN5-C.................................... 303
Option Communication Error ........................................... 296, 311
Option Frequency Reference .................................................. 463
Option Installation .............................................................. 378
Option Settings.................................................................. 197
Oscillation or Hunting.......................................................... 333
Output Current .................................................................. 458
Output Current 1 During Speed Search...................................... 157
Output Current at Previous Fault ............................................. 460
Output Frequency............................................................... 458
Output Frequency after Soft Start ............................................ 459
Output Frequency at Previous Fault.......................................... 460
Output Frequency Reduction During Overheat Alarm .................... 258
Output Frequency Resolution ................................................. 405
Output Ground Fault Detection Selection ............................. 259, 446
Output Phase Loss .............................................................. 300
Output Phase Loss Detection Level for Dynamic Audible Noise Control ...
Output Phase Loss Level for Dynamic Noise Control..................... 275
Output Phase Loss Protection ................................................. 446
Output Phase Loss Protection Selection ..................................... 258
Output Power.................................................................... 458
Output Power at Previous Fault............................................... 460
Output Terminal Status ........................................................ 458
Output Terminal Status at Previous Fault ................................... 460
Output Voltage at Previous Fault ............................................. 460
Output Voltage Detection Fault............................................... 310
Output Voltage Reference ..................................................... 458
ov............................................................................ 306, 316
Overcurrent ...................................................................... 301
Overexcitation Deceleration................................................... 248
Overexcitation Deceleration Gain ...................................... 265, 448
Overexcitation Operation Selection .................................... 265, 448
Overheat 1 (Heatsink Overheat) .............................................. 304
Overheat Alarm Level.................................................... 221, 446
Overheat Pre-Alarm Operation Selection ............................. 222, 446
Overload Protection ............................................................ 405
Overload Tolerance................... 396, 397, 398, 399, 400, 402, 403, 404
Overtorque Detection 1 ........................................................ 305
Overtorque Detection 2 ........................................................ 305
Overtorque Detection Operation.............................................. 255
Overvoltage...................................................................... 306
Overvoltage Protection......................................................... 405
Overvoltage Suppression Function ........................................... 249
Overvoltage Suppression Function Selection ............................... 249
ov Suppression Function Selection........................................... 444
P
P1000 Models .....................................................................29
Parameter Access Level........................................................ 137
Parameter Range Setting Error................................................ 318
Parameter Settings .............................................................. 118
Parameters for KEB Ride-Thru ............................................... 243
Parameters to Minimize Motor Hunting and Oscillation .................. 290
PASS ............................................................................. 316
Password ................................................................... 137, 143
Password Setting................................................................ 143
Password Settings............................................................... 137
P Control ......................................................................... 159
Peak Hold Current .............................................................. 463
Peak Hold Output Frequency ................................................. 463
Performance Life ............................................................ 343, 3
Performance Life Monitors Maintenance Monitors........................... 3
Periodic Inspection ............................................................. 341
Periodic Maintenance .......................................................... 221
PF ................................................................................. 306
Phase Order Selection .......................................................... 152
PID Accel/Decel Time ......................................................... 166
PID Block Diagram............................................................. 162
PID Control...................................................................... 159
Index
562
YASKAWA SIEP YAIP1U 01B AC Drive - P1000 Technical Manual