Yaskawa AC Drive-P1000 Industrial Fan User Manual
Page 563
PID Feedback 1 ................................................................. 464
PID Feedback High Detection Level......................................... 166
PID Feedback High Detection Time ......................................... 166
PID Feedback Input Methods ................................................. 160
PID Feedback Loss ....................................................... 300, 314
PID Feedback Loss Detection Selection..................................... 165
PID Feedback Low Detection Level ......................................... 165
PID Feedback Low Detection Time.......................................... 165
PID Fine Tuning ................................................................ 173
PID Function Setting ........................................................... 163
PID Input (feedback) ........................................................... 464
PID Input Limit ................................................................. 171
PID Monitors .................................................................... 285
PID Offset Adjustment......................................................... 163
PID Output....................................................................... 464
PID Output Gain Setting....................................................... 164
PID Output Level Selection ................................................... 164
PID Output Limit ............................................................... 163
PID Output Lower Limit....................................................... 171
PID Output Reverse Selection ................................................ 164
PID Output Reverse Selection 2 .............................................. 172
PID Primary Delay Time Constant ........................................... 163
PID Setpoint ..................................................................... 464
PID Setpoint Display Digits................................................... 169
PID Setpoint Input Methods................................................... 160
PID Setpoint Scaling ........................................................... 168
PID Setpoint Selection ......................................................... 167
PID Setpoint User Display .................................................... 169
PID Setpoint Value ............................................................. 167
PID Sleep ........................................................................ 166
PID Sleep Delay Time ......................................................... 166
PID Sleep Function Start Level ............................................... 166
PI Output Monitor Calculation Method...................................... 172
PI Setpoint Monitor Unit Selection........................................... 169
PI Unit Selection ................................................................ 171
Power Detection Filter Time .................................................. 174
Powering Up the Drive......................................................... 125
Power Ratings (Three-Phase 200 V Class)...................... 396, 397, 398
Power Ratings (Three-Phase 400 V Class)...................... 399, 400, 401
Power Ratings (Three-Phase 600 V Class)...................... 402, 403, 404
Power Unit Output Phase Loss 3 ............................................. 300
Predefined V/f Patterns ........................................................ 191
Preface..............................................................................16
Preparing the Ends of Shielded Cables ........................................98
Preset Reference Timing Diagram ........................................... 183
Previous Fault ................................................................... 460
PROFIBUS-DP Clear Mode Selection ...................................... 201
PROFIBUS-DP Data Format Selection...................................... 201
PROFIBUS-DP Node Address ............................................... 200
PROFIBUS-DP Parameters ................................................... 200
Programmable Run Timers for Real Time Clock (RTC).................. 275
Programming Mode ...................................................... 114, 118
Proportional Gain Setting (P) ................................................. 163
Protective Cover ..................................................................50
Protective Covers, Reattaching .................................................78
Protective Covers, Removing .............................................. 77, 78
Protective cover to prevent miswiring .........................................44
PTC ............................................................................... 229
Pulse Train Input................................................................ 231
Pulse Train Input Bias.......................................................... 231
Pulse Train Input Filter Time ................................................. 231
Pulse Train Input Gain ......................................................... 231
Pulse Train Input Minimum Frequency...................................... 232
Pulse Train Input Scaling ...................................................... 231
Pulse Train Input Terminal RP Function Selection ........................ 231
R
R-....................................................................................96
R/L1 ................................................................................83
R+...................................................................................96
R1-L11 .............................................................................83
Radiated and Radio Frequency Noise........................................ 390
Ramp to stop .................................................................... 149
Rated Current Depending on Carrier Frequency ........................... 409
Rated Current Setting Alarm .................................................. 321
Rated Output Capacity ............... 396, 397, 398, 399, 400, 402, 403, 404
Rated Output Current................. 396, 397, 398, 399, 400, 402, 403, 404
Rated Slip Error ................................................................. 323
Rated Voltage, Rated Frequency ... 396, 397, 398, 399, 400, 402, 403, 404
rdEr ............................................................................... 325
READ ............................................................................ 271
rEAd .............................................................................. 325
Reading Drive MEMOBUS/Modbus Register Contents .................. 496
Reading Parameter Settings ................................................... 325
Real Time Clock ................................................................ 275
Reattaching the Digital Operator ...............................................79
Reattaching the Front Cover ....................................................81
Reattaching the Protective Cover...............................................82
Reattaching the Terminal Cover ........................................... 77, 78
REMOTE ........................................................................ 122
Removing the Cooling Fan .................................................... 349
Removing the Digital Operator .................................................79
Removing the Front Cover ......................................................79
Removing the Protective Cover.................................................82
Removing the Terminal Cover............................................. 77, 78
Replacement Parts .............................................................. 343
Replacing the Drive ............................................................ 371
Reset Communication Parameters............................................ 199
RESET Key...................................................................... 109
Resistance Tuning Error ....................................................... 321
Response Messages from Drive to Master .................................. 493
Reverse Direction Output Example Time Chart............................ 221
Reverse Operation Selection .................................................. 151
Reverse Prohibited Error....................................................... 323
rF .................................................................................. 307
rH ................................................................................. 307
Rotational Auto-Tuning........................................................ 130
Rotational Auto-Tuning for V/f Control..................................... 129
RP...................................................................................95
rr................................................................................... 307
RS-422 Interface ................................................................ 488
RS-485 Interface ................................................................ 487
RTS Control Selection ......................................................... 490
Rubber Bushing ...................................................................36
rUn ................................................................................ 316
Run Command/Frequency Reference Source Selection Error............ 319
Run Command at Power Up................................................... 152
Run Command Method Selection ............................................ 491
Run Command Selection 1 .............................................. 148, 416
Run Command Selection 2 .................................................... 152
Index
YASKAWA SIEP YAIP1U 01B AC Drive - P1000 Technical Manual
563