Document Outline

• Start Here
  • System Requirements
  • Package Contents
  • Install ProSoft Configuration Builder Software
• To install ProSoft Configuration Builder from the ProSoft We
• To install ProSoft Configuration Builder from the CD-ROM
  • Setting Jumpers
  • Install the Module in the Rack
  • Connect your PC to the Processor
  • Open the Sample Ladder Logic
    • To Determine the Firmware Version of your Processor
    • Select the Slot Number for the Module
• To change the slot number
  • Configuring RSLinx
• If RSLogix is unable to establish communication with the pro
  • Download the Sample Program to the Processor
• To download the sample program from RSLogix 5000 to the Cont
  • Connect your PC to the Module
• Module Configuration
  • Installing and Configuring the Module
  • ProSoft Configuration Builder
    • Set Up the Project
      • Adding a Project
• To add a project to an existing project file:
  • Adding a Module
• To add a module to your project:
• To add a module to a different location:
  • Set Module Parameters
• To rename an object:
  • Module Entries
• To configure module parameters
  • Comment Entries
• To add comments to your configuration file:
  • Printing a Configuration File
• To print a configuration file:
  • [Module]
    • Module Type
    • Module Name
  • [Backplane 56]
    • Read Register Start
    • Read Register Count
    • Write Register Start
    • Read Register Count
    • Backplane Fail Count
    • Error/Status Block Pointer
  • [BSAPS Config]
    • Number of Signal Value
    • Signal List Number
    • Array Element Row
    • Array Element Column
    • SFirmware Enable
    • Immediate Response Mode
  • [BSAP Data Element]
    • Signal Type
    • Version No
    • Signal Addr
    • Hi DB
    • Lo DB
    • Hi AL
    • Lo AL
    • HH AL
    • LL AL
    • Base Name
    • Extension Name
    • Attribute Name
    • Signal Descriptor
  • [BSAP Port x]
    • Enable
    • Baud Rate
    • Parity
    • Data Bits
    • Stop Bits
    • RTS On
    • RTS Off
    • Use CTS Line
    • Slave ID
  • Download the Project to the Module
• To Download the Project File
  • Configuring a BSAP Master
    • BSAP Protocol
    • Required pin assignments
• Ladder Logic
  • Module Data Object (BSAPModuleDef)
    • Backplane Control Object
    • User Data Objects
    • Status Data
  • BSAP Message Data
    • BSAP Time Synchronization (BSAPDateAndTime)
• Diagnostics and Troubleshooting
  • Reading Status Data from the Module
    • Required Hardware
    • The Configuration/Debug Menu
      • Using the Diagnostic Window in ProSoft Configuration Builder
      • Navigation
        • Keystrokes
    • Main Menu
      • Viewing Version Information
      • Opening the Database Menu
      • Resetting diagnostic data
      • Opening the Backplane Menu
      • Opening the Protocol_Serial_BSAP Menu
      • Sending the Configuration File
      • Receiving the Configuration File
      • Warm Booting the Module
      • Exiting the Program
    • Database View Menu
      • Viewing Register Pages
      • Displaying the Current Page of Registers Again
      • Moving Back Through 5 Pages of Registers
      • Viewing the Previous 100 Registers of Data
      • Skipping 500 Registers of Data
      • Viewing the Next 100 Registers of Data
      • Viewing Data in Decimal Format
      • Viewing Data in Hexadecimal Format
      • Viewing Data in Floating Point Format
      • Viewing Data in ASCII (Text) Format
      • Returning to the Main Menu
    • Backplane Menu
      • Redisplaying the Menu
      • Viewing Version Information
      • Returning to the Main Menu
      • Viewing Configuration Information
      • Viewing Backplane Diagnostic Information
    • Protocol Serial BSAP Menu
      • Redisplaying the Menu
      • Viewing Version Information
      • Returning to the Main Menu
      • Viewing Configuration Information
      • Opening the Command List Menu
      • Opening the Serial Port Menu
      • Viewing Error and Status Data
  • LED Status Indicators
    • Clearing a Fault Condition
    • Troubleshooting
• Reference
  • Product Specifications
    • Features and Benefits
    • General Specifications
    • Hardware Specifications
    • Functional Specifications
  • Functional Overview
    • Introduction
    • Protocol Overview
    • General Concepts
      • Module Power Up
      • Main Logic Loop
      • ControlLogix Processor Not in Run
      • Backplane Data Transfer
      • Normal Data Transfer
        • Read Block
        • Write Block
        • Warm Boot
        • Cold Boot
      • Pass-Through Control Blocks
        • Pass-Through Time Synchronization
        • Formatted Pass-Through Control Block
        • Pass-Through Control Block Examples
    • Data Flow Between the MVI56-BSAPS Module and the ControlLogi
      • Slave Driver
  • Cable Connections
    • RS-232 Configuration/Debug Port
      • Disabling the RSLinx Driver for the Com Port on the PC
    • RS-232
      • RS-232: Modem Connection
      • RS-232: Null Modem Connection (Hardware Handshaking)
      • RS-232: Null Modem Connection (No Hardware Handshaking)
    • RS-422
    • RS-485
      • RS-485 and RS-422 Tip
    • DB9 to RJ45 Adaptor (Cable 14)
  • MVI56-BSAPS Status Data Area
• Support, Service & Warranty
  • How to Contact Us: Technical Support
  • Return Material Authorization (RMA) Policies and Conditions
    • All Product Returns:
    • Procedures for Return of Units Under Warranty:
    • Procedures for Return of Units Out of Warranty:
    • Purchasing Warranty Extension:
  • LIMITED WARRANTY
    • What Is Covered By This Warranty
    • What Is Not Covered By This Warranty
    • Disclaimer Regarding High Risk Activities
    • Intellectual Property Indemnity
    • Disclaimer of all Other Warranties
    • Limitation of Remedies **
    • Time Limit for Bringing Suit
    • No Other Warranties
    • Allocation of Risks
    • Controlling Law and Severability
• Index