Yamaha DME - Manual (Page 460)

Chapter 6 Component Guide
DME Designer Owner’s Manual 460
Rev+Chorus
One input, two
output reverb and
chorus effects in
parallel. Rev Time 0.3 to 99.0 s Reverb time
Ini.Dly 0.0 to 500.0 ms Initial delay before reverb begins
Hi.Ratio 0.1 to 1.0 High-frequency reverb time ratio
Diff. 0 to 10 Spread
Density 0 to 100% Reverb density
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency
Rev/Cho 0 to 100% Reverb and chorus balance (0% = all reverb, 100%
= all chorus)
Freq. 0.05 to 40.00 Hz Modulation speed
AM.Depth 0 to 100% Amplitude modulation depth
PM.Depth 0 to 100% Pitch modulation depth
Mod.Dly 0.0 to 500.0 ms Modulation delay time
Wave Sine, Tri Modulation waveform
Rev->Chorus
One input, two
output reverb and
chorus effects in
series. Rev Time 0.3 to 99.0 s Reverb time
Ini.Dly 0.0 to 500.0 ms Initial delay before reverb begins
Hi.Ratio 0.1 to 1.0 High-frequency reverb time ratio
Diff. 0 to 10 Spread
Density 0 to 100% Reverb density
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency
Rev Bal. 0 to 100% Reverb and chorused reverb balance (0% = all
chorused reverb, 100% = all reverb)
Freq. 0.05 to 40.00 Hz Modulation speed
AM.Depth 0 to 100% Amplitude modulation depth
PM.Depth 0 to 100% Pitch modulation depth
Mod.Dly 0.0 to 500.0 ms Modulation delay time
Wave Sine, Tri Modulation waveform
Rev+Flange
One input, two
output reverb and
flanger effects in
parallel. Rev Time 0.3 to 99.0 s Reverb time
Ini.Dly 0.0 to 500.0 ms Initial delay before reverb begins
Hi.Ratio 0.1 to 1.0 High-frequency reverb time ratio
Diff. 0 to 10 Spread
Density 0 to 100% Reverb density
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency
Rev/Flg 0 to 100% Reverb and flange balance (0% = all reverb, 100%
= all flange)
Freq. 0.05 to 40.00 Hz Modulation speed
Depth 0 to 100% Modulation depth
Mod.Dly 0.0 to 500.0 ms Modulation delay time
FB.Gain -99 to +99% Feedback gain (plus values for normal-phase
feedback, minus values for reverse-phase
feedback)
Wave Sine, Tri Modulation waveform
Rev->Flange
One input, two
output reverb and
flanger effects in
series. Rev Time 0.3 to 99.0 s Reverb time
Ini.Dly 0.0 to 500.0 ms Initial delay before reverb begins
Hi.Ratio 0.1 to 1.0 High-frequency reverb time ratio
Diff. 0 to 10 Spread
Density 0 to 100% Reverb density
HPF THRU, 21.2 Hz to 8.00 kHz High-pass filter cutoff frequency
LPF 50.0 Hz to 16.0 kHz, THRU Low-pass filter cutoff frequency
Rev Bal. 0 to 100% Reverb and flanged reverb balance (0% = all
flanged reverb, 100% = all reverb)
Freq. 0.05 to 40.00 Hz Modulation speed
Depth 0 to 100% Modulation depth
Mod.Dly 0.0 to 500.0 ms Modulation delay time
FB.Gain -99 to +99% Feedback gain (plus values for normal-phase
feedback, minus values for reverse-phase
feedback)
Wave Sine, Tri Modulation waveform
Effect Type Parameter Setting Range Function