Solid state relay specifications, 4 specifications & factory defaults – Electro Cam PL-1746 Series User Manual
Page 137
9-4 Specifications & Factory Defaults
Solid State Relay Specifications
AC Outputs
Part # EC-OAC240-3
Output Voltage:
24 VAC rms minimum
280 VAC rms maximum
Output Current:
30 mA rms minimum
3 amps rms maximum @/below 35
°
C (95
°
F).
Above 35
°
C derate 50 mA/
°
C (27.8 mA/
°
F)
Input Voltage:
5 VDC nominal
8 VDC maximum
Turn On Time:
100
µ
s maximum @ 60 Hz
Turn Off Time:
8.3 ms maximum @ 60 Hz
Off State Leakage:
2 mA AC rms @ 120 VAC rms, 60 Hz
Operating Temp.
-30
°
C to +70
°
C (–22
°
to +158
°
F)
DC Output, 60 VDC
Part # EC-ODC060-3
Output Voltage:
0 to 60 VDC
Output Current:
3 amps DC @/below 35
°
C (95
°
F)
Above 35
°
C derate 35.7 mA/
°
C (19.8 mA/
°
F)
Turn On Time:
50
µ
s maximum
Turn Off Time:
50
µ
s maximum
Off State Leakage:
1
µ
A DC maximum @ 24 VDC
Operating Temp.
-30
°
C to +70
°
C (–22
°
to +158
°
F)
DC Outputs, 200 VDC
Part # EC-ODC200-1 (Slimline)
Output Voltage:
0 to 200 VDC
Output Current:
1 amp DC @/below 45
°
C (113
°
F).
Above 45
°
C derate 18 mA/
°
C (10 mA/
°
F)
Turn On:
50
µ
s maximum
Turn Off:
50
µ
s maximum
Off State Leakage:
1
µ
A maximum
Operating Temp.
-30
°
C to +70
°
C (–22
°
to +158
°
F)
Analog Output, 0-10 VDC
Part # EC-SANL-010V
Resolution:
12 Bits (4096 Increments)
Output Voltage:
0 to 10 VDC
Output Current:
10 mA maximum
Load Resistance:
1 K Ohm minimum
Linearity:
±
0.3% full scale @ 25
°
C (77
°
F)
Analog Output, 4-20 mA
Part # EC-SANL-420M
Resolution:
12 Bits (4096 Increments)
Output Current:
4 to 20 mA DC
Load Resistance:
450 Ohm maximum
Linearity:
±
0.3% full scale @ 25
°
C (77
°
F)
Reed Relays
EC-ORR000-0 (SLIMLINE)
Output Type:
N/O Reed Relay Contacts
Contact Rating:
10 VA maximum
Switching Voltage:
100 VDC or 130 VAC maximum
Switching Current:
0.5 A maximum
Carry Current:
1.5 A maximum
Turn On Time:
500 ms
Turn Off Time:
500
µ
s
Mechanical Life:
5 x 10
6
cycles
Operating Temp:
-30 to +70
°
C (-22
°
to +158
°
F)
Note: The maximum current rating for each module installed in the PS-4108 rack is as stated in the module's specifi-
cations, OR 1.5 amps, whichever is less.