Watlow EZ-ZONE ST - Manual (Page 42)

Watlow EZ-ZONE ® ST • 40 • Chapter 4 Setup Page
Setup Page
Display
Parameter Name
Description
Range Default
Modbus
Relative
Address
CIP
Class
Instance
Attribute
hex (dec)
Pro DP
Index
Par
ID
RUI/
GTW
Mod-
bus
Data
Type
&
Read/
Write
[``Ai]
[`Set]
Analog Input Menu
[`Sen]
[ SEn] Analog Input (1 to 2)
Sensor Type
Set the analog sensor type
to match the device wired
to this input.
Note:
There is no open-
sensor detection
for process inputs .
[`oFF] Off (62)
[``tC] Thermocouple (95)
[`mu] Millivolts (56)
[uolT] Volts dc (104)
[`MA] Milliamps dc (112)
[r0;1H] RTD 100 Ω (113)
[r1;0H] RTD 1,000 Ω (114)
Instance 1
Map 1 Map 2
42 368
Instance 2
Map 1 Map 2
70
458
0x68 (104)
1 to 2
5
3 4005 Inst. 1
368
Inst. 2
528
uint
RWES
[`Lin]
[ Lin] Analog Input (1 to 2)
Linearization
Set the linearization to
match the thermocouple
wired to this input.
[```J] J (46)
[```F] F (30)
[```E] E (26)
[```d] D (23)
[```C] C (15)
[```b] B (11)
[```t] T (93)
[```S] S (84)
[```r] R (80)
[```n] N (58)
[```H] K (48)
J Instance 1
Map 1 Map 2
43 370
Instance 2
Map 1 Map 2
71
460
0x68 (104)
1 to 2
6
4 4006 Inst. 1
370
Inst. 2
530
uint
RWES
[`Rt;L]
[ rt.L] Analog Input (1 to 2)
RTD Leads
Set to match the number
of leads on the RTD wired
to this input.
[```2] 2 (1)
[```3] 3 (2)
2 Instance 1
Map 1 Map 2
44 372
Instance 2
Map 1 Map 2
72
462
0x68 (104)
1 to 2
7
- - - - 4007 Inst. 1
372
Inst. 2
532
uint
RWES
[Unit]
[Unit] Analog Input (1 to 2)
Units
Set the type of units the
sensor will measure.
[`A;tP] Absolute Temperature
(1540)
[``rh] Relative Humidity
(1538)
[`Pro] Process (75)
[PWr] Power (73)
Process Instance 1
Map 1 Map 2
- - - - 442
Instance 2
Map 1 Map 2
- - - - 532
0x68 (104)
1 to 2
0x2A (42)
5 4042 - - - - uint
RWES
Note:
Some values will be rounded off to fit in the four-character display .
Full values can be read with other interfaces .
If there is only one instance of a menu, no submenus will appear .
R: Read
W: Write
E: EE-
PROM
S: User
Set
To go to the Setup Page from the Home Page, press both
the Up ¿ and Down ¯ keys for six seconds. [``Ai] will
appear in the upper display and [`Set] will appear in
the lower display.
• Press the Up ¿ or Down ¯ key to move through
the menus.
• Press the Advance Key ‰ to move to a submenu.
• Press the Up ¿ or Down ¯ key to move through
the submenus.
• Press the Advance Key ‰ to move through the pa-
rameters of the menu or submenu.
• Press the Infinity Key ˆ to move backwards
through the levels: parameter to submenu; sub-
menu to menu; menu to Home Page.
• Press and hold the Infinity Key ˆ for two seconds
to return to the Home Page.
Note:
Avoid continuous writes within loops . Excessive writes to EEPROM
will cause premature EEPROM failure . The EEPROM is rated for
1,000,000 writes . Navigate to Setup Page under the CoM menu and
set prompt Non-volatile Save
[`nU;S]
to No .