Futaba 10CG 2.4GHz User Manual

Page 44

Advertising
background image

44

GOAL of EXAMPLE:

STEPS:

INPUTS:

Set up aileron triple rates on SWITCH
C
with travel settings of 75% (normal),
25% (slow roll) and 140% (extreme
aerobatics) and exponential settings of
0%, +15%, and -40% respectively.

N O T E : T h i s n o r m a l r a t e h a s n o
exponential so it has a very linear,
normal feel. This slow roll rate has
positive exponential (the opposite of
what most people normally use), which
makes the servos more responsive
around center. This makes the servos
feel the same around center in the
normal and low rates, but still gives a
very slow roll rate at full stick.

The 3D rate (extreme aerobatics) has a
very high distance of travel nearly twice
that of the normal rate. Therefore, using
a very high negative exponential setting
softens how the servos respond around
center stick. This makes the servos
respond similarly around center stick
for a more comfortable feel.

Many modelers like to set up all 3 triple
rates on a single 3-position switch,
creating a “slow and pretty mode”,
a “normal mode”, and a “wild stunts
mode” all with the flip of a single
switch. To do so, simply set up rates
for all 3 controls and assign all 3 to the
same 3-position switch.

Open D/R,EXP function.

for 1 second.

(If ADVANCE,

again.)

C

to D/R,EXP.

Choose the channel to change
(Ex: aileron is already selected)

C

to desired channel.

Optional: change switch assignment.

C

to SW1.

to C.

Confirm switch is in desired position
and set rate. (Ex: up = high rate, 75%).

C

to D/R>.

C to up position.

AILERON STICK.

to 75%.

AILERON STICK.

to 75%.

Move SWITCH to 2nd rate position and
set this particular rate.
(Ex: center = low rate, 25%).

C to center position.

AILERON STICK.

to 25%.

AILERON STICK.

to 25%.

Optional: if using a 3 position SWITCH,
move SWITCH to 3rd position and set
this rate (Ex: down = 3D rate, 140%).

C to down position.

AILERON STICK.

to 140%.

AILERON STICK.

to 140%.

Optional: instead of using a switch,
you can set high rates to be triggered
when the stick moves past a certain
point. To test this, set aileron high rate
to 25%. Now set switch assignment to
AIL (90%). Move AILERON STICK
to the right and notice the huge jump in
travel after the stick moves 90% of its
distance.

C

to SW1.

to AILE (90%).

C

to D/R>.

AILERON STICK.

to 25%.

AILERON STICK.

to 25%.

A I L E R O N S T I C K a n d w a t c h

screen graph. See the change?!

You may also change the trigger point
by holding the stick at the desired point,
then pressing and holding the DIAL.

Set each rate’s EXP.
(Ex: 0%, +15%, -40%)

C

to EXP>.

C to up position.

&RQ¿UPEXP reads 0.

C to down position.

AILERON STICK.

to +15%.

AILERON STICK.

to + 15%.

C to center position.

repeat to set low rate expo to -40%.

Repeat above steps for elevator and rudder.

Close.

Where next?

6HWXSÀLJKWWLPHUVVHHS
Set up TRAINER functions: see p. 47.
Adjust the sensitivity of the trims: see p. 48.
Set up twin aileron servos: see p. 51.
Set up twin elevator servos: see p. 57.
6HWXSSURJUDPPDEOHPL[HVWRPHHW\RXUVSHFL¿FQHHGVVHHS

Advertising