Futaba 10CG 2.4GHz - Manual (Page 78)

78
$/22.$77+(5$',2
6GLID-SPECIFIC FUNCTIONS STEP BY STEP.
Those functions which are identical to the ACRO setups are referred directly to those pages.
MODEL TYPE : This function of the PARAMETER submenu is used to select the type of model programming to be used.
GLIDER TYPES:
%HIRUHGRLQJDQ\WKLQJHOVHWRVHWXSDJOLGHURUVDLOSODQH¿UVW\RXPXVWGHFLGHZKLFKMODEL TYPEEHVW¿WV\RXUDLUFUDIW
• ACRO
IRUVRPHDHUREDWLFVORSHJOLGHUVACRO is a better choice because of functions it offers that the GLID types do not.
• ACRO provides:
• SNAP-ROLL,
• AILEVATOR (twin elevator servo support),
• AIRBRAKE (a more assignable version of BUTTERFLY).
• For nitro-powered sailplanes: IDLE-DOWN, THR-CUT, THROTTLE-NEEDLE mixing and THROTTLE DELAY programming.
• But ACRO  ODFNV SURJUDPPLQJ IRU IXOOVSDQ DLOHURQV DQG VHSDUDWH 2))6(7 WULPV IRU HDFK ÀLJKW FRQGLWLRQ  1RUPDO
Start, Speed, Distance and Landing.
• GLID(1A+1F): The GLID(1A+1F) MODEL TYPE is intended for sailplanes with one or two aileron servos (or none), and a single
ÀDS VHUYR RU WZR FRQQHFWHG ZLWK D \FRQQHFWRU 7KLV TYPE is meant to be a very simplistic version to set up a basic
JOLGHUZLWKRXWDORWRIDGGHGIHDWXUHV$GGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOH
• GLID(2A+1F): The GLID(2A+1F) MODEL TYPE LVLQWHQGHGIRUVDLOSODQHVZLWKGXDODLOHURQVHUYRVDQGDVLQJOHÀDSVHUYR RU
WZRFRQQHFWHGZLWKD\FRQQHFWRU $GGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOH7KHVHÀLJKWFRQGLWLRQVFRQWDLQGLIIHUHQWRIIVHW
trims and aileron differentials to make the sailplane perform certain maneuvers more easily.
• GLID(2A+2F): The GLID(2A+2F) MODEL TYPE supports dual flap servos that can also act as ailerons, creating full-span
DLOHURQVDQGÀDSV$GGLWLRQDOÀLJKWFRQGLWLRQVDYDLODEOH7KHVHÀLJKWFRQGLWLRQVFRQWDLQGLIIHUHQWRIIVHWWULPVDQGDLOHURQ
differentials to make the sailplane perform certain maneuvers more easily.
GOAL of EXAMPLE: STEPS: INPUTS:
C h a n g e m o d e l 1 i s MODEL T YPE t o
GLID(1A+1F)
.
N O T E : T h i s i s o n e o f t h e s e v e r a l
f u n c t i o n s t h a t t h e r a d i o re q u i re s
FRQ¿UPDWLRQWRPDNHDFKDQJH
Confirm you are currently using the
proper model memory. (Ex: 1) On home screen, check model nameand
number on top left.
If it is not the correct model (Ex: 1), use
MODEL SELECT
, p. 25.
Open PARAMETER submenu. for 1 second. (If ADVANCE, again.)
to 2nd page of menu.
C to PARAMETER.
Change the MODEL TYPE.
&RQ¿UPWKHFKDQJH C to TYPE. to GLID(1A+1F).
for one second.
Are you sure? &RQ¿UPDWLRQGLVSOD\V
WRFRQ¿UP
Close.
GLID(1A+1F)
(FLAPERON)
AIL1
FLP2
(CH1)
AIL2
FLP1
(CH6)
AIL1
(CH1)
AIL2
(CH7)
FLP
(CH6)
GLID(2A+1F)
AIL1
(CH1)
FLP1
(CH6)
FLP2
(CH5)
AIL2
(CH7)
GLID(2A+2F)