Futaba FX-40 - Manual (Page 100)

100 <Model Menu (Airplane/Glider Functions)>
ŏ5HWXUQWR0RGHO0HQX
*\UR >&RUUHVSRQGLQJPRGHOW\SH@ $LUSODQHJOLGHUJHQHUDO
7KLVIXQFWLRQLVXVHGZKHQD*<$6HULHVJ\UR
is used to stabilize the fuselage attitude. The
VHQVLWLYLW\DQGRSHUDWLRQPRGH 1RUPDOPRGH*<
mode) can be changed with a switch.
ŏ7KUHHUDWHV 5DWH5DWH5DWH FDQEH
switched.
ŏ8SWRD[HV *\UR*\UR*\UR FDQEH
simultaneously controlled.
*Initial setting does not assign a sensitivity channel. Use the
ŏ7RXFKWKH>*\UR@EXWWRQLQWKH0RGHO0HQX
to call the setup screen shown below.
Function menu of the Linkage Menu to assign the sensitivity
FKDQQHO *\UR*\UR*\UR  XVHG WR D YDFDQW FKDQQHO
beforehand.
Set [ACT] and [Trim] other than Function to [NULL].
ŏ7KHRSHUDWLRQPRGH $9&6125 DQGVHQVLWLYLW\RI
the 3 axes Gyro/Gyro2/Gyro3 can be set.
ŏ *URXSVLQJOH PRGH VZLWFKLQJ
(Gr./Sngl)
(For more information, see the description
at the back of this manual.)
ŏ7KUHHUDWHV 5DWH5DWH5DWH FDQEHXVHG
ŏ7RXFKWKH$&7EXWWRQRIWKHUDWHWREHXVHGDQGVHWWKHIXQFWLRQWR
$&7 >21@RU>2))@ 
ŏ :KHQ D )XWDED *<$ J\UR LV XVHG ZKHQ >*<@ W\SH LV V HOHFWHG WKH
VHQVLWLYLW\VHWYDOXHLVGLUHFWO\UHDGLQERWKWKH$9&6DQG125PRGHV
ŏ :KHQ VHWWLQJ D VZLWFK WRXFK WKH VZLWFK EXWWRQ WR FDOO WKH 6ZLWFK!
VFUHHQDQGWKHQVHOHFWWKHVZLWFKDQGVHWLWV21GLUHFWLRQ
(For a description of the switch selection method, see the description at
the end of this manual.)
([DPSOH 6HWWLQJD[HVXVLQJD*<$DQG*<$ D[HVJ\UR
ŏ:LQJW\SH $LOHURQVHUYRVPRXQWHGIXVHODJHVHOHFWHG
ŏ6HW*\UR *<$ &+*\UR *<$ &+*\UR *<$ &+ DWWKH
)XQFWLRQPHQXRIWKH/LQNDJH0HQX
ŏ5DWH>2))@>*<@>6:(@>125@>@>125@>@>125@> @>*U@
5DWH>,1+@>*<@>18//@>$9&6@>@>$9&6@>@>$9&6@>@>*U@
5DWH>2))@>*<@>6((@>$9&6@>@>$9&6@>@>$9&6@>@>*U@
*When separating the conditions, set to [Sngl].
6HWVRWKDW5DWHLVWXUQHGRQDWWKHEDFNSRVLWLRQRIVZLWFK(DQG5DWHLVWXUQHG21DWWKH
front position.
Since switch E is turned OFF at the center, Rate 2 remains [INH].