Futaba FX-40 - Manual (Page 79)

79 <Model Menu (Common Functions)>
6HWWLQJPHWKRGV
ŏ*URXSVLQJOHPRGHVHOHFWLRQ
$FWLYDWLQJ IXQFWLRQV IRU RQO\ WKH VHOHFWHG
conditions:
 7RXFK WKH *URXS EXWWRQ DQG VZLWFK WR WKH
6QJOPRGH
*Each time the button is touched, it toggles between the Gr.
and Sngl modes.
ŏ0L[LQJPRGHVHOHFWLRQ
Using the offset mode:
 7RXFK WKH 0RGH EXWWRQ DQG VZLWFK WR WKH
Offset mode.
*Each time the button is touched, it toggles between the Mix
and Offset modes.
ŏ0L[LQJVHWXSVFUHHQVHOHFWLRQ
1. Touch the button of the mixing you want
to set. The mixing setup screen is displayed.
$FWLYDWHWKHIXQFWLRQ
$FWLYDWHWKHIXQFWLRQE\WRXFKLQJWKH>,1+@
button.
*Each time this button is touched, it toggles between [INH]
and [ON/OFF].
ŏ0L[LQJ 212)) VZLWFK VHWWLQJ DQG 212))
direction switching
*An ON/OFF switch is not set even when the function is
activated.
 :KHQ \RX ZDQW WR WXUQ PL[LQJ 212)) E\
VZLWFK WRXFK WKH >18//@ EXWWRQ WR FDOO WKH
6ZLWFK!VFUHHQDQGWKHQVHOHFWWKHVZLWFK
and its ON direction.
*For a description of the selection method, see [Switch
Setting Method] at the back of this manual.
ŏ0DVWHU FKDQQHO VHWWLQJ H[FHSW RIIVHW W\SH
mixing)
7RXFKWKH0DVWHUEXWWRQWRFDOOWKH)XQFWLRQ
menu and select the master channel.
7ROLQNWKLVPL[LQJZLWKRWKHUPL[LQJWRXFKWKH
button at the left of the master channel and
VHOHFWOLQN
*Each time the button is touched, it toggles between mixing
direction + and - and "No display" (no link).
*Master channel control can be set to stick, VR, and other
simple travels which do not include ATV, AFR, D/R, mixing
setting, etc. In this case, display the <Switch> screen by
touching the [H/W] button and then select master channel
side control.
ŏ6ODYHFKDQQHOVHWWLQJ
7RXFKWKH6ODYHEXWWRQWRFDOOWKH)XQFWLRQ
menu and select the slave channel.
 7R OLQN WKLV PL[LQJ ZLWK RWKHU PL[LQJ WRXFK
the button at the right-hand side of the slave
FKDQQHODQGVHOHFWOLQN
*Each time the button is pressed, it toggles between mixing
direction + and - and "No display" (no link).
ŏ7ULPPRGH212))VHWWLQJ
7RWXUQWKHWULPPRGH212))WRXFKWKH7ULP
button on the screen.
*When mixing includes master side trim, set the Trim button
to [ON]. When mixing does not include master side trim, set
the Trim button to [OFF].
*Each time this button is pressed, it toggles between [ON]
and [OFF].
*This is effective when the master channel is set by Function.
ŏ6ODYHFKDQQHO$)5PRGH 67.ń67.
 :KHQ /LQN LV VHW DW WKH VODYH VLGH DQG \RX
ZDQW WR DGG $)5 '5  WR WKH PL[LQJ UDWH
VHOHFW>21@:KHQ\RXGRQRWZDQWWRDGG
$)5 '5 WRWKHPL[LQJUDWHVHOHFW>2))@
*Each time this button is pressed, it toggles between [ON]
and [OFF].
*This is effective when making corrections when the fuselage
is the same but the rudder angles are substantially different.
ŏ0L[LQJFXUYHW\SHVHOHFWLRQ
1. Touch the curve type selection button of the
curve type you want to use to display the
selection screen and then select the curve
you want to use.
*For a description of the curve setting method, see the
description at the back of this manual.
ŏ)LQHWXQLQJWULPVHWWLQJ
 :KHQ XVLQJ WKH FXUYH ILQH WXQLQJ IXQFWLRQ
WRXFK WKH >18//@ EXWWRQ RI WKH )LQH 7XQLQJ
LWHP WR FDOO WKH 6ZLWFK! VFUHHQ DQG WKHQ
VHOHFWWKHOHYHU95HWF\RXZDQWWRXVH
)RUDGHVFULSWLRQRIWKH¿QHWXQLQJWULPVHWWLQJPHWKRGVHH
the description at the back of this manual.
ŏ6HUYRVSHHGVHWWLQJ
 :KHQ VHWWLQJ WKH VHUYR VSHHG WRXFK WKH
6SHHGEXWWRQ7KH6HUYR6SHHGVHWXSVFUHHQ
is displayed.
*For a description of the servo speed setting method, see the
description at the back of this manual.
*Offset mixing changes the speed. Use the Speed In and
Speed Out buttons to readjust the speed..
The mixing switch can set a delay with a different rate at
starting and stopping.
*This function is inactive when a mixing switch is not set.