Futaba FX-40 - Manual (Page 14)

14 <Before Use>
•Angle adjustment of the antenna
<RX FDQ FKDQJH WKH DQJOH RI WKH DQWHQQD DV
you like. Use 2.5mm hexagonal wrench to turn
counterclockwise to release the screw on the left
of the antenna holder, and change the angle of the
antenna as you like, then retighten.
Ɣ6FUHZ
LED monitor
The color of the FX-40 logo mark shows the
status of the transmitter.
(LED Display)
• When you turn on the transmitter, FX-40 logo
shows different colors, and then the color
stays constantly pink. The FX-40 logo blinks
yellow very rapidly while internal processing
is carried out after the power is turned on.
Once the internal processing is over, the logo
turns to pink color.
• The FX-40 logo blinks blue slowly when No is
selected for transmit.
• The FX-40 logo turns on blue when you use
DSC cable or when the trainer function is set
at student's side.
• The FX-40 logo blinks red slowly when you
attach the RF module that is different from
the setting.
• Under the normal usage (radio wave is being
emitted), the FX-40 logo turns on green.
Precautions when opening the rear cover and
working inside
When opening the rear cover and performing
VZLWFK UHSODFHPHQW VWLFN WHQVLRQ DGMXVWPHQW RU
other work inside the transmitter, open the rear
cover as described below. Also, always observe the
precautions.
1. Turn off the power to the transmitter.
/RRVHQWKHWZRÀ[LQJVFUHZVDQGUHPRYHWKH
rear cover.
Fixing screws
3. Remove the battery stopper by pulling it
forward while pushing the lock button in the
DUURZGLUHFWLRQ1H[WVOLGHWKHEDWWHU\RXW
Battery stopper
Battery
CAUTION
When the rear cover is opened, always
remove the battery before performing switch
replacement or other work.
'URSSLQJVFUHZVWRROVRURWKHUREMHFWVLQWRWKHWUDQVPLWWHU
while performing work may cause a short circuit and dam-
age the transmitter.
4. Replace the switch, etc. (Refer to each work
item.)
CAUTION
Be careful not to damage the internal PC board
ZLWKDWRRORURWKHUREMHFWGXULQJZRUN
Be careful not to touch the protruding parts of
the switch and PC board.
7RXFKLQJSURWUXGLQJSDUWVPD\UHVXOWLQLQMXU\
5. At the end of work, reload the battery and
fasten it with the battery stopper.
6. After fitting the antenna side of the rear
cover, align the front side of the cover with
the groove in the rear case and close the
cover.
)DVWHQWKHFRYHUZLWKWKHWZRÀ[LQJVFUHZV
Switch reallocation
<RXFDQUHDOORFDWHWKHWRJJOHVZLWFKHVDV\RX
like.
(Default settings)
• SA : 3 positions; Alternate; Short lever
• SB
: 3 positions; Alternate; Short lever
• SC : 3 positions; Alternate; Long lever
• SD : 3 positions; Alternate; Short lever
• SE
: 3 positions; Alternate; Short lever
• SF : 2 positions; Alternate; Long lever
• SG : 3 positions; Alternate; Short lever
• SH
: 3 positions; Alternate; Short lever
<RX FDQ FKRRVH VZLWFK DQG VHW WKH 21GLUHFWLRQ LQ WKH
setting screen of the function menu.