Futaba FX-40 - Manual (Page 42)

42 <Model Basic Setting Procedure>
1. Model addition and call
Default setting assigns 1 model to the FX-40. To
add new models or to call a model already set, use the
Model Select function of the Linkage Menu.
This is convenient when calling a model after
registering the model names in advance. (The data of
up to 30 models can be saved at the transmitter. Data
can also be saved to the accessory Data-Pack.)
The currently called model is displayed at the top
RIWKHVFUHHQ%HIRUHÀ\LQJDQGEHIRUHFKDQJLQJDQ\
VHWWLQJVDOZD\VFRQ¿UPWKHPRGHOQDPH
Please be aware that the transmitter will stop
transmitting when you change the model.
When a new model is added, the Model Type Select
screen and Frequency/Modulation mode/Receiver ID
setup screen automatically appear. Change, or check
that they match the type, frequency, and receiver type
of the model used.
2. Model type and swash type selection
When a separate model type is already selected,
select helicopter with the Model Type function of the
Linkage Menu, and then select the swash type matched
to the helicopter.
Helicopter basic setting procedure
3. Flight condition addition
The transmitter can install up to eight flight
conditions per model. You can assign all switches
including sticks, switches, trim levers and trim switches
as flight-condition selection switches. You can also
add delayed mixing to these functions in order to
avoid sudden changes. Moreover, you can set priority
RUGHUIRUÀLJKWFRQGLWLRQVZKHQ\RXVHWPRUHWKDQRQH
condition. In addition, you can copy conditions and/or
change names of conditions. This command may also
be used to define what switches and/or controls are
XVHGWRDFWLYDWHHDFKÀLJKWFRQGLWLRQ
The Condition Select function automatically
DOORFDWHVWKH&RQGLWLRQIRUHDFKPRGHOW\SH1RUPDOLV
the default condition, and is the only one active when a
QHZPRGHOW\SHLVGH¿QHG7KLVFRQGLWLRQLVDOZD\VRQ
and remains on until other conditions are activated by
switches.
The Condition Delay can be programmed for each
channel. The Condition Delay is used to change the
servo throw smoothly when switching conditions.
*HQHUDOÀLJKWFRQGLWLRQVHWWLQJH[DPSOH
ŏ1RUPDO  8VHLQLWLDOVHWWLQJFRQGLWLRQVRSHUDWH
ZKHQVZLWFK2))
8VHIURPHQJLQHVWDUWLQJWRKRYHULQJ
ŏ ,GOH XS   6ZLWFK VHWWLQJ H[DPSOH  2SHUDWH
DW6:(FHQWHU
8VHLQƒVWDOOWXUQORRSUROOLQJVWDOOWXUQDQGRWKHU
PDQHXYHUV
ŏ ,GOH XS   6ZLWFK VHWWLQJ H[DPSOH  2SHUDWH
DW6:(IRUZDUGVLGH
8VHLQUROOV
ŏ 7KURWWOH KROG  6ZLWFK VHWWLQJ H[DPSOH
2SHUDWHDW6:*IRUZDUGVLGH
8VHLQDXWRURWDWLRQ
The priority is throttle hold/idle up 2/idle up 1/
normal. Throttle hold has the highest priority.
Add other conditions, as required.