Futaba FX-40 - Manual (Page 96)

96 <Model Menu (Airplane/Glider Functions)>
7ULP0L[ >&RUUHVSRQGLQJPRGHOW\SH@ *OLGHUDLOHURQVRUPRUH
These functions call the ailerons, elevators, and
ÀDSV FDPEHUÀDSVEUDNHÀDSV WULPRIIVHWUDWHV
SUHVHWDFFRUGLQJWRWKHÀLJKWVWDWH
The amount of ailerons, elevator, and flaps
FDPEHUÀDSEUDNHÀDS WULPRIIVHWFDQEHVHWWR
a switch.
As an example 7ULP0L[ can be set up for
ODXQFKLQJZLWKVSHHGÀDSVDQGDLOHURQVGURSSHG
and a slight amount of up elevator.
7ULP PL[
 can be used for high speed flying, with both
DLOHURQVDQGVSHHGÀDSVUHÀH[HGVOLJKWO\DQGDELW
of down elevator.
The trim functions can be activated during
ÀLJKWE\VHWWLQJDVZLWFK7RSUHYHQWVXGGHQWULP
FKDQJHVZKHQVZLWFKLQJÀLJKWFRQGLWLRQVDGHOD\
can be set to provide a smooth transition between
the two. Trim Mix 2 will have priority over Trim
Mix 1.
ŏ5HWXUQWR0RGHO0HQX
ŏ:KHQDÀQHWXQLQJ95LVVHWRQWKHQH[WSDJH  WKHDLOHURQV
DQGÁDSVWULPUDWHVFDQEHDGMXVWHG
Touch the corresponding button and adjust the rate with the
adjustment buttons displayed on the screen.
ŏ 7KH DLOHURQV IODSV DQG HOHYDWRUV
offset rate can be adjusted.
Touch the corresponding button
a n d a d j u s t t h e r a t e w i t h t h e
adjustment buttons displayed on
the screen.
ŏ7RXFKWKH>7ULP0L[@EXWWRQLQWKH0RGHO0HQXWR
call the setup screen shown below.
(The display screen is an example. The actual screen depends on the
PRGHOW\SH7KHVFUHHQVKRZQEHORZLVIRUDLOHURQVDQGÀDSV
(Touch the [1/2] button to switch to page 2.)
ŏ 7RXFK WKH $&7 EXWWRQ DQG VHW WKH IXQFWLRQ WR $&7
21 
ŏ :KHQ VHWWLQJ D VZLWFK WRXFK WKH 6ZLWFK EXWWRQ
to call the <Switch> screen, and then select the
VZLWFKDQGVHWLWV21GLUHFWLRQ $OZD\V21DW18//
setting)
(For a description of the switch selection method, see the description at
the back of this manual.)
([DPSOH
7RXFKWKH$&7EXWWRQDQGVHWWKHWULPPL[IXQFWLRQ
WR>21@
*When separating the settings for each condition, touch the
group mode button and set it to [Sngl].
6HOHFWWKH212))VZLWFK
6HOHFWWKH>0DQXDO@RU>$XWR@PRGH
,QWKH>$XWR@PRGHDOVRVHOHFWDQDXWR6:7KLV
switch can be linked to a stick, etc.
<Speed>
,Q 7KHRSHUDWLRQVSHHGDWVZLWFK21FDQEHVHW
2XW 7KHUHWXUQVSHHGDWVZLWFK2))FDQEHVHW
<Fine Tuning>
The offset rate can be varied in the Fine Tuning
QXPHULF UDQJH VHW DW VFUHHQ >@ E\ 95 HWF
selection.
&RQGLWLRQ'HOD\!
:KHQÁLJKWFRQGLWLRQVDUHVHWWKHRSHUDWLRQVSHHG
FDQEHVHWIRUHDFKFRQGLWLRQ&RQGLWLRQGHOD\
operation can be interrupted and each rudder
quickly returned to its original position by selecting a
cut switch.