Sensoray 2600 - Manual (Page 4)

2600 Family Instruction Manual iii Table of Contents
Table of Contents
7.6.8 SetModes32 .........................................42
7.6.9 GetModes32.........................................42
7.7 Specifications ..........................................42
Model 2612 Strain Gauge/RTD Module
8.1 Introduction............................................43
8.2 Conversion Modes..................................43
8.2.1 Oversample Ratio ................................43
8.2.2 Speed Multiplier ..................................43
8.3 Excitation ................................................44
8.3.1 Self-Heating Errors ..............................44
8.4 Analog Inputs .........................................44
8.4.1 Reference Voltage Range ....................44
8.4.2 Input Voltage Range ............................44
8.5 Hardware Configuration.......................44
8.5.1 Bridge Completion Shunt ....................44
8.5.2 Remote Sense Shunts...........................45
8.5.3 Field Wiring Connectors......................45
8.5.3.1 RJ-45 Connectors....................................45
8.5.3.2 Terminal Blocks......................................45
8.6 Reset ........................................................46
8.7 Actions.....................................................46
8.7.1 SetMode ...............................................46
8.7.2 GetInputs..............................................46
8.7.3 SetVoltages ..........................................47
8.7.4 ReadEeprom.........................................47
8.7.5 WriteEeprom........................................47
8.8 Specifications ..........................................48
Model 2620 Counter Module
9.1 Introduction............................................50
9.1.1 Diagnostic LEDs..................................50
9.2 Hardware Configuration.......................50
9.2.1 IOM Network Connector .....................51
9.2.2 Field Wiring Terminal Blocks .............51
9.3 Reset ........................................................51
9.4 Actions.....................................................51
9.4.1 SetMode ...............................................52
9.4.2 SetCommonControl .............................53
9.4.3 SoftTrigger...........................................53
9.4.4 GetStatus ..............................................54
9.4.5 SetPreload0 ..........................................54
9.4.6 SetPreload1 ..........................................54
9.4.7 GetCounts ............................................ 54
9.4.8 GetCountsTs ........................................ 54
9.5 Applications............................................55
9.5.1 Incremental Encoder Interface............. 55
9.5.2 Pulse Generator ................................... 55
9.5.3 PWM Generator................................... 56
9.5.4 Pulse Width Measurement................... 56
9.5.5 Period Measurement ............................ 56
9.5.6 Frequency Measurement ..................... 56
9.6 Specifications..........................................57
Model 2650 Relay Module
10.1 Introduction............................................58
10.2 Hardware Configuration.......................58
10.2.1 IOM Network Connector..................... 58
10.2.2 Interlock Power Connectors ................ 58
10.2.3 Relay Power Selection Shunt .............. 59
10.2.4 I/O Connectors..................................... 59
10.2.5 Reserved Connectors ........................... 59
10.3 Reset ........................................................60
10.4 Status Flags.............................................60
10.5 Actions.....................................................60
10.5.1 GetInputs ............................................. 60
10.5.2 GetOutputs........................................... 60
10.5.3 SetOutputs ........................................... 61
10.6 Specifications..........................................61
Model 2652 SSR Module
11.1 Introduction............................................62
11.2 Hardware Configuration.......................62
11.2.1 IOM Network Connector..................... 62
11.2.2 Interlock Power Connectors ................ 62
11.2.3 Relay Power Selection Shunt .............. 63
11.2.4 I/O Connectors..................................... 63
11.2.5 Reserved Connectors ........................... 64
11.3 Channel Operating Modes ....................64
11.3.1 Output Operation ................................. 64
11.3.2 Input Operation.................................... 64
11.3.3 Output Modes ...................................... 64
11.3.4 Input Debounce ................................... 64
11.4 Reset ........................................................64
11.5 Status Flags.............................................65
11.6 Actions.....................................................65