Kramer 4x4 Audio and Dante Mixer - Manual (Page 39)

Kramer Electronics Ltd.
FC-404NETxl – Protocol 3000 37
Function Description Syntax Parameters/Attributes Example
FEATURE-
LIST? Get feature state
according to the feature
ID. COMMAND
#FEATURE-LIST?  feature_id <CR>
FEEDBACK
~nn@FEATURE-LIST  feature_id , ir_state <CR><LF>
feature_id – Feature ID)
1 – Maestro
2 – Room controller
3 – Maestro panel
ir_state – IR interface
0 – disable
1 – enable
Get the room controller
feature state (for the room
controller 1):
#FEATURE-LIST?  1 <CR>
FILE-
HANDLED For internal use only.
FW - TYPE ? Get the current FW
type status.
Used by Kramer
Network and KUpload
to identify recovery
process.
COMMAND
#FW-TYPE?  <CR>
FEEDBACK
~nn@FEATURE-LIST  fw_type <CR><LF>
Fw_type –
0 – Application
1 – Safe mode (kboot)
Get the current FW type
status:
#FW-TYPE?  <CR>
HELP Get command list or
help for specific
command. COMMAND
#HELP <CR>
#HELP  cmd_name <CR>
FEEDBACK
1. Multi-line:
~nn@Device  cmd_name ,  cmd_name… <CR><LF>
To get help for command use: HELP (COMMAND_NAME) <CR><LF>
~nn@HELP  cmd_name: <CR><LF>
description <CR><LF>
USAGE:usage <CR><LF>
cmd_name – Name of a specific
command
Get the command list:
#HELP <CR>
To get help for
AV-SW-TIMEOUT:
HELP
 av-sw-timeout <C
R>
LOGIN
(internal)
Set protocol
permission.
The permission
system works only if
security is enabled with
the “SECUR”
command.
LOGIN allows the user
to run commands with
an End User or
Administrator
permission level.
When the permission
system is enabled,
LOGIN enables running
commands with the
User or Administrator
permission level
When set, login must
be performed upon
each connection
It is not mandatory to
enable the permission
system in order to use
the device
In each device, some
connections allow
logging in to different
levels. Some do not
work with security at all.
Connection may logout
after timeout.
COMMAND
#LOGIN  login_level , password <CR>
FEEDBACK
~nn@LOGIN  login_level , password  ok <CR><LF>
or
~nn@LOGIN  err  004 <CR><LF>
(if bad password entered)
login_level – Level of
permissions required (User or
Admin)
password – Predefined password
(by PASS command). Default
password is an empty string
Set the protocol permission
level to Admin (when the
password defined in the
PASS command is 33333):
#LOGIN  admin , 33333 <CR
>
LOGIN?
(internal)
Get current protocol
permission level.
The permission
system works only if
security is enabled with
the “SECUR”
command.
For devices that
support security,
LOGIN allows the user
to run commands with
an End User or
Administrator
permission level.
In each device, some
connections allow
logging in to different
levels. Some do not
work with security at all.
Connection may logout
after timeout.
COMMAND
#LOGIN?  <CR>
FEEDBACK
~nn@LOGIN  login_level <CR><LF>
login_level – Level of
permissions required (User or
Admin)
Get current protocol
permission level:
#LOGIN? <CR>
LOGOUT
(internal
)
Cancel current
permission level.
Logs out from End
User or Administrator
permission levels to Not
Secure.
COMMAND
#LOGOUT <CR>
FEEDBACK
~nn@LOGOUT  ok <CR><LF>
#LOGOUT <CR>