Kramer electronics ltd – Kramer 4x4 Audio and Dante Mixer User Manual
Page 43
Kramer Electronics Ltd.
FC-404NETxl
– Protocol 3000
41
Function
Description
Syntax
Parameters/Attributes
Example
X-AUD-LVL
Set audio level of a
specific signal.
This is an Extended
Protocol 3000
command.
COMMAND
#X-AUD-LVL
<direction_type>
.
<port_type>
.
<port_index>
.
<si
gnal_type>
.
<index>
,
audio_level
<CR>
FEEDBACK
~nn@X-AUD-LVL
<direction_type>
.
<port_type>
.
<port_index>
.
<signal_type>
.
<index>
,
audio_level
<CR><LF>
The following attributes comprise
the signal ID:
▪
<direction_type>
–
o
IN
o
OUT
▪
<port_type>
–
o
ANALOG_AUDIO
o
ANALOG_JACK
o
DANTE
▪
port_index>
– The port
number as printed on the front
or rear panel: 1 to 4 for analog
audio, and 1 for Dante
▪
signal_type>
– Signal ID
attribute:
o
AUDIO
▪
<index>
– Indicates a specific
channel number when there
are multiple channels of the
same type: 1 to 4 for Dante,
and 1 for Analog audio
audio_level
– Audio level in dB
(range between -100 to +15)
depending of the ability of the
product
Set the audio level of analog
audio specific signal to 10:
#X-AUD-LVL
IN
.
ANALOG_
AUDIO
.
4
.
AUDIO
.
1
,
10
<CR
>
X-AUD-
LVL?
Get audio level of a
specific signal.
This is an Extended
Protocol 3000
command.
COMMAND
#X-AUD-LVL?
<direction_type>
.
<port_format>
.
<port_index>
.
<signal_type>
.
<index>
<CR>
FEEDBACK
~nn@X-AUD-LVL
<direction_type>
.
<port_format>
.
<port_index>
.
<signal_type>
.
<index>
,
audio_level
<CR><LF>
The following attributes comprise
the signal ID:
▪
<direction_type>
–
o
IN
o
OUT
▪
<port_type>
–
o
ANALOG_AUDIO
o
ANALOG_JACK
o
DANTE
▪
port_index>
– The port
number as printed on the front
or rear panel: 1 to 4 for analog
audio, and 1 for Dante
▪
signal_type>
– Signal ID
attribute:
o
AUDIO
▪
<index>
– Indicates a specific
channel number when there
are multiple channels of the
same type: 1 to 4 for Dante,
and 1 for Analog audio
audio_level
– Audio level in dB
(range between --100 to +15)
depending of the ability of the
product
Get the audio level of a
specific signal:
#X-AUD-LVL?
out
.
analo
g_audio
.
1
.
audio
.
1
<CR>
X-AUD-
MODE
Set line/Mic mode.
This is an Extended
Protocol 3000
command.
COMMAND
#X-AUD-MODE
<direction_type>
.
<port_type>
.
<port_index>
.
<s
ignal_type>
.
<index>
,
mode
<CR>
FEEDBACK
~nn@X-AUD-MODE
<direction_type>
.
<port_type>
.
<port_index>
.
<signal_type>
.
<index>
,
mode
<CR><LF>
The following attributes comprise
the signal ID:
▪
<direction_type>
–
o
IN
▪
<port_type>
–
o
ANALOG_AUDIO
▪
<port_index>
– The port
number as printed on the front
or rear panel 1 to 4.
▪
<signal_type>
–
o
AUDIO
▪
<index>
– Indicates a specific
channel number when there
are multiple channels of the
same type 1 to 2.
mode
–
1
– Line
2
– Mic
Set AUDIO IN 2 to Mic
mode:
#X-AUD-MODE
IN
.
ANALOG
_AUDIO
.
2
.
AUDIO
.
1
,
2
<CR
>
X-AUD-
MODE?
Get line/Mic mode.
This is an Extended
Protocol 3000
command.
COMMAND
#X-AUD-MODE?
<direction_type>
.
<port_type>
.
<port_index>
.
<
signal_type>
.
<index>
<CR>
FEEDBACK
~nn@X-AUD-MODE
<direction_type>
.
<port_type>
.
<port_index>
.
<signal_type>
.
<index>
,
mode
<CR><LF>
The following attributes comprise
the signal ID:
▪
<direction_type>
–
o
IN
▪
<port_type>
–
o
ANALOG_AUDIO
▪
<port_index>
– The port
number as printed on the front
or rear panel 1 to 4.
▪
<signal_type>
–
o
AUDIO
▪
<index>
– Indicates a specific
channel number when there
are multiple channels of the
same type 1 to 2.
mode
–
1
– Line
2
– Mic
Get AUDIO IN 1 to audio
mode:
#X-AUD-MODE?
IN
.
ANALO
G_AUDIO
.
5
.
AUDIO
.
1
<CR>