Kramer electronics ltd – Kramer 4x4 Audio and Dante Mixer User Manual
Page 45
Kramer Electronics Ltd.
FC-404NETxl
– Protocol 3000
43
Function
Description
Syntax
Parameters/Attributes
Example
X-MIX-LVL
Set DSP matrix cross-
point MIX level in dB.
This is an Extended
Protocol 3000
command.
COMMAND
#X-MIX-LVL
OUT
.
<port_type>
.
<port_index>
.
<signal_type>
.
<i
ndex>
,
IN
.
<port_type>
.
<port_index>
.
<signal_type>
.
<index>,
dB
<CR>
FEEDBACK
~nn@X-MIX-LVL
OUT
.
<port_type>
.
<port_index>
.
<signal_type>
.
<index>
,
IN
.
<port_type>
.
<port_index>
.
<signal_type>
.
<inde
x>,dB
<CR><LF>
The following attributes comprise
the primary signal ID (suffix 1) and
follower signal ID (suffix 2 or
greater):
▪
<direction_type>
– IN
o
IN
o
OUT
▪
<port_type>
–
o
ANALOG_AUDIO
o
ANALOG_JACK
o
DANTE
▪
< port_index>
– The port
number as printed on the front
or rear panel: 1 to 4 for analog
audio, and 1 for Dante
▪
signal_type>
– Signal ID
attribute:
o
AUDIO
▪
<index>
– Indicates a specific
channel number when there
are multiple channels of the
same type: 1 to 4 for Dante,
and 1 for Analog audio
Set analog audio 1 and
Dante 1 cross-point level to -
25dB:
#X-MIX-LVL
OUT.ANALOG
_AUDIO.1.AUDIO.1,IN.D
ANTE.1.AUDIO.1,-
25
<CR>
X-MIX-
LVL?
Get DSP matrix cross-
point MIX level in dB.
This is an Extended
Protocol 3000
command.
COMMAND
#X-MIX-LVL?
OUT
.
<port_type>
.
<port_index>
.
<signal_type>
.
<
index>
,
IN
.
<port_type>
.
<port_index>
.
<signal_type>
.
<index
<CR>
FEEDBACK
~nn@X-MIX-LVL
OUT
.
<port_type>
.
<port_index>
.
<signal_type>
.
<index>
,
IN
.
<port_type>
.
<port_index>
.
<signal_type>
.
<inde
x>,dB
<CR><LF>
The following attributes comprise
the primary signal ID (suffix 1) and
follower signal ID (suffix 2 or
greater):
▪
<direction_type>
– IN
o
IN
o
OUT
▪
<port_type>
–
o
ANALOG_AUDIO
o
ANALOG_JACK
o
DANTE
▪
< port_index>
– The port
number as printed on the front
or rear panel: 1 to 4 for analog
audio, and 1 for Dante
▪
signal_type>
– Signal ID
attribute:
o
AUDIO
▪
<index>
– Indicates a specific
channel number when there
are multiple channels of the
same type: 1 to 4 for Dante,
and 1 for Analog audio
Get analog audio 3 and
Dante 2 cross-point level:
#X-MIX-LVL?
OUT.ANALO
G_AUDIO.3.AUDIO.1,IN.
DANTE.1.AUDIO.2
<CR>
X-MIX-
MUTE
Set Matrix cross-point
mute syntax.
This is an Extended
Protocol 3000
command.
COMMAND
#X-MIX-MUTE
OUT
.
<port_type>
.
<port_index>
.
<signal_type>
.
<
index>
,
IN
.
<port_type>
.
<port_index>
.
<signal_type>
.
<index>
,dB
<CR
FEEDBACK
~nn@X-MIX-MUTE
OUT
.
<port_type>
.
<port_index>
.
<signal_type
>
.
<index>
,
IN
.
<port_type>
.
<port_index>
.
<signal_type>
.
<ind
ex>,<mute_state>
<CR><LF>
The following attributes comprise
the signal ID:
▪
<direction_type>
–
Direction of the port:
o
IN
– Input
o
OUT
– Output
▪
<port_format>
– Type of
signal on the port:
o
ANALOG_AUDIO
o
DANTE
▪
port_index>
– The port
number as printed on the front
or rear panel: 1 to 4 for analog
audio, and 1 for Dante
▪
signal_type>
– Signal ID
attribute:
o
AUDIO
▪
<index>
– Indicates a specific
channel number when there
are multiple channels of the
same type: 1 to 4 for Dante,
and 1 for Analog audio
<mute_state>
–
o
ON=1
o
OFF=0
Set mute status of analog
audio output 1 and Dante
audio cross-point 3 to on:
#X-MIX-MUTE
OUT.ANALOG_AUDIO.1.AU
DIO.1,IN.DANTE.1.AUDI
O.3,1
<CR>