Kramer electronics ltd – Kramer 4x4 Audio and Dante Mixer User Manual
Page 40
Kramer Electronics Ltd.
FC-404NETxl
– Protocol 3000
38
Function
Description
Syntax
Parameters/Attributes
Example
MODEL?
Get device model.
This command
identifies equipment
connected to
FC-
404NETxl
and notifies
of identity changes to
the connected
equipment. The Matrix
saves this data in
memory to answer
REMOTE-INFO
requests.
COMMAND
#MODEL?
<CR>
FEEDBACK
~nn@MODEL
model_name
<CR><LF>
model_name
– String of up to 19
printable ASCII chars
Get the device model:
#MODEL?
<CR>
NAME
Set machine (DNS)
name.
The machine name
is not the same as the
model name. The
machine name is used
to identify a specific
machine or a network in
use (with DNS feature
on).
COMMAND
#NAME
machine_name
<CR>
FEEDBACK
~nn@NAME
machine_name
<CR><LF>
machine_name
– String of up to 15
alpha-numeric chars (can include
hyphen, not at the beginning or end)
Set the DNS name of the
device to room-442:
#NAME
room-442
<CR>
NAME?
Get machine (DNS)
name.
The machine name
is not the same as the
model name. The
machine name is used
to identify a specific
machine or a network in
use (with DNS feature
on).
COMMAND
#NAME?
<CR>
FEEDBACK
~nn@NAME
machine_name
<CR><LF>
machine_name
– String of up to 15
alpha-numeric chars (can include
hyphen, not at the beginning or end)
Get the DNS name of the
device:
#NAME?
<CR>
NAME-RST
Reset machine (DNS)
name to factory default.
Factory default of
machine (DNS) name is
“KRAMER_” + 4 last
digits of device serial
number.
COMMAND
#NAME-RST
<CR>
FEEDBACK
~nn@NAME-RST
ok
<CR><LF>
Reset the machine name
(S/N last digits are 0102):
#NAME-
RST
kramer_0102
<CR>
NET-
CONFIG
Set a network
configuration.
Parameters
[DNS1]
and
[DNS2]
are
optional.
For Backward
compatibility, the
id
parameter can be
omitted. In this case,
the Network ID, by
default, is 0, which is
the Ethernet control
port.
If the gateway
address is not
compliant to the subnet
mask used for the host
IP, the command will
return an error. Subnet
and gateway
compliancy specified by
RFC950.
COMMAND
#NET-CONFIG
netw_id
,
net_ip
,
net_mask
,
gateway
,
[dns1]
,
[dns2
]
<CR>
FEEDBACK
~nn@NET-CONFIG
netw_id
,
net_ip
,
net_mask
,
gateway
<CR><LF>
netw_id
– Network ID–the device
network interface (if there are more
than one).
0
– ETH control port
1
– DANTE ETH Port
net_ip
– Network IP
net_mask
– Network mask
gateway
– Network gateway
Set the device network
parameters to IP address
192.168.113.10, net mask
255.255.0.0, and gateway
192.168.0.1:
#NET-CONFIG
0
,
192
.
168
.
113
.
10
,
255
.
255
.
0
.
0
,
1
92
.
168
.
0
.
1
<CR>
NET-
CONFIG?
Get a network
configuration.
COMMAND
#NET-CONFIG?
netw_id
<CR>
FEEDBACK
~nn@NET-CONFIG
netw_id
,
net_ip
,
net_mask
,
gateway
<CR><LF>
netw_id
– Network ID–the device
network interface (if there are more
than one).
0
– ETH control port
1
– DANTE ETH Port
net_ip
– Network IP
net_mask
– Network mask
gateway
– Network gateway
Get network configuration:
#NET-CONFIG?
id
<CR>