Document Outline

• Contents
• 1.0 Introduction
  • 1.1 Safety
  • 1.2 Overview
  • 1.3 Operating Modes
  • 1.4 Keypad Functions
  • 1.5 Tare Recall
  • 1.6 Annunciators LEDs
  • 1.7 Bar Graph LEDs
• 2.0 Installation
  • 2.1 Unpacking and Assembly
  • 2.2 Leveling
  • 2.3 Making Power Connections
  • 2.4 Enclosure Disassembly
  • 2.5 Load Cell Wiring
  • 2.6 Wire Specifics
  • 2.7 Cable Grounding
    • 2.7.1 Serial Communications
    • 2.7.2 Digital I/O
  • 2.8 Enclosure Reassembly
  • 2.9 Board Removal
  • 2.10 Battery Replacement
  • 2.11 Installing Option Cards
  • 2.12 Replacement Parts and Assembly Drawings
• 3.0 Configuration
  • 3.1 Menu Navigation
  • 3.2 Audit Menu
  • 3.3 Calibration Menu
  • 3.4 Setup Menu
    • 3.4.1 SCALE Submenu
    • 3.4.2 FEATUR Submenu
    • 3.4.3 FEATUR Menu, REGULA / INDUST Submenu
    • 3.4.4 Serial, PFORMT, DIG I/O, VERS Submenus
  • 3.5 Test Menu
  • 3.6 Time and Date Menu
  • 3.7 ACCUM Menu
  • 3.8 BRIGHT Menu
  • 3.9 ID Menu
• 4.0 Calibration
  • 4.1 Front Panel Calibration
  • 4.2 EDP Command Calibration
  • 4.3 Revolution® Calibration
  • 4.4 More About Calibration
    • 4.4.1 Adjusting Final Calibration
• 5.0 Operation
  • 5.1 Range Mode
    • 5.1.1 Value Set: Keyed
    • 5.1.2 Value Set: Push
  • 5.2 Target Weight Mode
    • 5.2.1 Value Set: Keyed
    • 5.2.2 Value Set: Push
  • 5.3 Target Percent Mode
    • 5.3.1 Value Set: Keyed
    • 5.3.2 Value Set: Push
  • 5.4 IDs
    • 5.4.1 Setting an ID
    • 5.4.2 Using a Stored ID
    • 5.4.3 WeighVault
  • 5.5 Negative Checkweighing
• 6.0 Serial Commands
  • 6.1 The Serial Command Set
    • 6.1.1 Key Press Commands
    • 6.1.2 ID Commands
    • 6.1.3 Reporting Commands
    • 6.1.4 Clear and Reset Commands
    • 6.1.5 Parameter Setting Commands
    • 6.1.6 Normal Mode Commands
    • 6.1.7 Unique Commands
  • 6.2 Custom Stream Formatting
• 7.0 Print Formatting
  • 7.1 Print Formatting Commands
  • 7.2 Customizing Print Formats
    • 7.2.1 Using the EDP Port
    • 7.2.2 Using the Front Panel
    • 7.2.3 Using Revolution®
• 8.0 WLAN Option Card
  • 8.1 WLAN Card Installation
• 9.0 Appendix
  • 9.1 Error Messages
  • 9.2 Using the XE EDP Command
  • 9.3 Status Messages
    • 9.3.1 Using the P EDP Command
    • 9.3.2 Using the ZZ EDP Command
  • 9.4 Continuous Output (Stream) Format
  • 9.5 Digital Filtering
    • 9.5.1 DIGFLx Parameters
    • 9.5.2 DFSENS and DFTHRH Parameters
    • 9.5.3 Setting the Digital Filter Parameters
    • 9.5.4 Audit Trail Support
  • 9.6 Regulatory Mode Functions
  • 9.7 Updating CW-90/90X Firmware
  • 9.8 Specifications