FARGO electronic HDPii - Manual (Page 370)

RESTRICTED USE ONLY Fargo Electronics, Inc.
HDPii High Definition Card Printer/Encoder User Guide (Rev. 1.1) 17-2
D
Darkness, 16-4
DB-9, 16-4
DC (Direct Current), 16-4
DC Motor, 16-4
Default, 16-4
Default button, 7-43
Defined Area(s) check box, 7-87
Defined Area(s) option, 7-85
Defrag, 16-4
Delete button – K Panel, 7-83
DIP switches (Dual In-line Package Switches), 16-4
Direct-to-Card (DTC) Printing, 16-5
direct-to-card printing, 7-2
disable printing, 7-37
disk cleanup utility, 5-31
Dither, 16-5
dither method, 7-44
DMA (Direct Memory Access), 16-3
Dongle, 16-5
Dot, 16-5
Dot pitch, 16-5
Download, 16-5
DPI (Dot Per Inch), 16-5
DRAM (Dynamic Random Access Memory), 16-5
Driver, 16-5
Driver control, 2-24
Duplex Printing, 16-5
dwell temperature, 7-15
Dwell Time, 7-7, 16-6
Dye Migration, 16-6
Dye-Sub Intensity slide, 7-41
dye-sub printed image, 7-41
Dye-Sublimation, 2-16, 16-6
Dye-Sublimation Cyan panel, 2-20
Dye-Sublimation Magenta panel, 2-20
dye-sublimation Ribbon Panels, 7-41
Dye-Sublimation Yellow panel, 2-20
E
E-card, 16-6
E-card Docking Station, 16-6
ECP Mode (Enhanced Capabilities Port Mode), 16-6
Edge-to-Edge, 16-6
Edge-to-Edge printing, 7-15
EE Memory, 16-6
EEPROM (Electrically Erasable Programmable Read
Only Memory), 16-6
embedded contaminants, 2-21
Emissions Standards, 2-5
Encode Station, 2-19
Encoder (Smart Card), 16-6
Encoder (wheel), 16-7
encoding instructions, 7-37
Encoding Mode, 7-65
Encoding Options, 2-10
End Sentinel (ES)., 7-77
Engine, 16-7
EOF (End Of Form), 16-7
EPP (Enhanced Parallel Port), 16-7
EPROM (Electronically Programmable Read Only
Memory), 16-7
Escape sequence, 16-7
ESD, 1-2, 7-1, 10-30
ESD (ElectroStatic Discharge), 16-7
Ethernet, 16-7
F
factory default settings/Default button, 7-58
Fargo Technical Support, 14-1
Fargo Technical Support via the Web, 14-1
feed card into encoder, 5-31
Feeder Station, 2-19
Field Separator (FS), 7-77
Film, 7-58, 16-7
Film Options, 2-11
Film particles, 7-7
Film Storage Temperature, 2-11
Film transfer parameters, 7-2
Firmware, 16-7
Flash Memory, 16-8
Flipper Table, 2-25
Font, 16-8
FPGA (Field Programmable Gate Array), 16-8
Full bleed, 16-8
Full Card option, 7-84
Functional Specifications, 2-16
G
Gamma, 16-8
Glossy / Matte, 16-8
Glossy PVC, 16-8
Glossy-PVC or Matte-PVC options, 7-58
Graphical Device Interface (GDI), 16-8
Gray Scale, 16-8
Gray/Align YMCK, 5-32
H
Halftoning, 16-8
Hard Drive, 16-9
hard Drive space
adequate or inadequate, 5-31
Hardware, 16-9
Head, 16-9
Heat Seal, 7-2, 16-9
Heat sink, 16-9
HiCo (High Coercivity), 16-9
High Coercivity, 7-65
High Coercivity UltraCard IIIs, 7-65
Horizontal adjustment, 7-54
HTML (HyperText Markup Language), 16-9
HTTP (HyperText Transfer Protocol), 16-9
Humidity, 2-11
I
IC (Integrated Circuit), 16-9
IC smart cards/proximity cards, 7-2