Quadra-Fire Castile Pellet Insert CASTILEI-MBK - Manual (Page 22)

Page 22 7022-122 January 19, 2011
R
Castile Pellet Insert
H. Surround and Cast Trim Set
I ncluded in Surround Kit: (2) side surrounds, left and
right; (1) surround top; (1) fastener package.
Included in Cast Trim Kit: (2) cast trim legs, left and right; (1)
cast trim header; (2) cast trim footers, left and right
Tools Needed: 4-6 inch long Philips head screwdriver, pliers
and fl at head screwdriver.
Do not pick up assembled appliance by corners.
It is too heavy and may damage the surrounds.
Pick up from center.
CAUTION
1. Place the peel and stick round felt vibration insulation
pads on the front side in each corner of the top metal
piece and on the back side in each corner of the top cast
piece. Figure 23.1 on page 23
2. Lay surround face down on a fl at protected surface to
prevent scratching.
3. Using the Philips screwdriver attach the side surrounds
to the top surround using 2 sheet metal screws provided
with the kit on each side.
4. Assemble Cast Trim and attach to surround:
a) Place corresponding cast trim pieces (2 cast trim sides
and 1 cast trim header) underneath the surround set, also
face down. Align the holes in the metal pieces with the 5
bosses on the top cast piece and 2 bosses on each side
piece. Figure. 22.1.
b) Attach the magnets to the magnet brackets with one
countersink screw each. Attach magnet and bracket to
the metal surround sides with magnet facing the front as
shown in Figure. 23.2 on page 23.
c) Place cast footers under metal sides aligning the top and
bottom holes.
d) The 9 mounting clips are shipped in one long strip. Use
your hands or pliers to break them apart.
e) Each clip has a clearance notch to allow room for the cast
on the boss. Place the clips over the boss so that the
notch is facing the outer edge of the surround. Figure
23.3 on page 23.
f) It is best to install all of the 1/4-20 screws only half way
at fi rst to allow for adjustments. After adjustment tighten
the 2 screws in each footer fi rst and then work your way
around to the rest.
5. Remove the cast sides before attaching the surround
and trim. Lift up the top to expose the thumb screws that
secure the cast sides. Remove the thumb screw and top
bracket and then remove the cast side. NOTE: The right
cast side bracket has the hopper cut out switch attached.
Remove the retainer from the right side and allow to hang
down into the insert or disconnect the switch when remov-
ing side.
6. Install the power cord in the surround.
7. If power enters the appliance on the right side: Using
the pliers, attach cord restraint 12 inches from the female
end of the cord and then press into the right side panel.
Figure 21.2 on page 21.
8. If power enters appliance on the left side: The cord will
have to be routed through the back of the insert. When
routing the power cord, keep cord lying fl at as possible,
keeping the cord away from all exhaust surfaces and
moving parts. After routing, install cord restraint and press
into the left side panel.
9. Slide surround over the top of the insert into place. Sur-
round attaches to bottom and top of insert sides with the
supplies 1/4 inch screws.
10. Plug cord into inlet on junction box routing the wire as
shown in Figure 21.3 on page 21.
11. Install plug into unused hole.
Figure 22.2
Thumb
Screw
Bracket
Surround Set
attaches to top
and bottom of
insert sides.
G. Surround & Trim Set, Econo (Cont’d)
Figure 22.1
View of "L" Bracket
installed