Wiegmann WAX-MSSN4 Series - Manual (Page 14)

A B N 1 2 , S D N 1 2 , S D N 1 2 P L , N 4 1 2 C D , N 4 1 2 C S T D , & N 4 1 2 C S S S T D S E R I E S
E N C L O S U R E S N E M A 1 2 F L A N G E D S I N G L E D O O R D I S C O N N E C T
F14
www.hubbell-wiegmann.com
Data Subject To Change Without Notice
Allen-Bradley
• 1494V disconnect switches with flange-mount
variable depth operating mechanisms and
1494V flange-mounted variable depth operating
mechanisms for circuit breakers
• 140U flexible cable operating mechanisms and
140U molded case circuit breakers
• 1494C cable-operated disconnect switches with
flange-mount handles
• 194RC cable-operated flange-mount handles for
use with the NFPA 79 compliant 194R IEC rotary
disconnect switches
Allen-Bradley 1494V-R1, -R2 and -W2 operating
handles and Allen-Bradley 1494F disconnect
devices or 1494D circuit breaker operators will
NOT fit these enclosures.
When using a Bulletin 1494V disconnect switch,
order:
* 1. A disconnect switch with operating
mechanism (Bulletin 1494V)
* 2. Bulletin 1494-H1 operating handle (Use
Bulletin 1494-H2 for enclosure catalog
number SDN12603812A)
* 3. A connecting rod [Bulletin 1494V-RA1 for
8.00" (203mm) and 10.00" (254mm) deep
enclosures; Bulletin 1494V-RA2 for 12.00"
(305mm) and 16.00" (406mm) deep
enclosures; two of Bulletin 1494-RB2 for
400 amp or 600 amp switch in a
SDN12603812A]
* 4. A trailer fuse block kit, if required (Bulletin 1494V)
* 5. A fuse clip kit, if required
6. Line and load connectors, if required
** 7. Door hardware (Bulletin 1494V-L1 for
2-point latching or Bulletin 1494V-L1
and 1494V-L2 for 3-point door latching)
When using a Bulletin 1494V circuit breaker
operating mechanism, order:
1. A circuit breaker (C-H)
2. A circuit breaker operating mechanism
(Bulletin 1494V)
3. An operating handle (Bulletin 1494V-H11)
4. A connecting rod [Bulletin 1494V-RA1 for
8.00" (203mm) and 10.00" (254mm) deep
enclosures or Bulletin 1494V-RA2 for 12.00"
(305mm) and 16.00" (406mm) deep enclosures]
** 5. Door hardware (Bulletin 1494V-L1 for
2-point latching or Bulletin 1494V-L1
and 1494V-L2 for 3-point door latching)
Allen-Bradley 1494 F Series See F23-F26
ABB Controls
When using a disconnect switch, order:
1. A flange operated switch (fusible or non-fusible)
2. A shaft [DSFHS-12 for 8.00” (203mm),
10.00" (254mm) and 12.00" (305mm) deep
enclosures or DSFHS-17 for 16.00”
(406mm) deep enclosures]
3. A handle (DSFGN-HS12)
** 4. Door hardware (FH-DHK for 2-point latching
or FH-DHK and FH-3RL for 3-point latching)
When using a circuit breaker, order:
1. A circuit breaker (ABB)
* 2. An operating mechanism
* 3. A shaft [FHS-12 for 8.00” (203mm), 10.00"
(254mm) and 12.00" (305mm) deep enclo-
sures or FHS-17 for 16.00” (406mm) deep
enclosures]
* 4. Handle mechanism (FHN-HS12)
** 5. Door hardware (FH-DHK for 2-point latching
or FH-DHK and FH-3RL for 3-point latching)
Eaton Cutler-Hammer
When using a Type C361 disconnect switch, order:
* 1. A disconnect switch with an operating
mechanism
* 2. An operating handle (C361H1 or C361H3)
** 3. Door hardware (C361KJ4 or C361KJ6 for
2-point latching, C361KJ4 or C361KJ6 and
C361KR for 3-point latching)
When using a Type C371 circuit breaker
operating mechanism with a C-H circuit
breaker, order:
1. A circuit breaker
* 2. An operating mechanism
* 3. An operating handle
** 4. Door hardware (C361KJ4 or C361KJ6 for
2-point latching, C361KJ4 or C361KJ6 and
C361KR for 3-point latching)
When using a C-H circuit breaker with a Flex
Shaft
™ handle mechanism, order:
1. A circuit breaker
2. A complete Flex Shaft
™ handle mechanism
** 3. Door hardware (C361KJ4 or C361KJ6 for
2-point latching, C361KJ4 or C361KJ6 and
C361KR for 3-point latching)
General Electric
When using a disconnect switch, order:
1. A disconnect switch (Type QMR or QMW)
2. A fuse clip kit or no-fuse kit
3. A flange handle (STDA1 or STDA2)
4. A variable depth operating mechanism
** 5. Door hardware (TDV1 for 2-point latching
or TDV1 and TDV3 for 3-point latching)
When using a circuit breaker with a Spectra Flex ™
cable operator, order:
1. A circuit breaker
2. A flange-mounted handle mechanism
3. A breaker-mounted mechanism
4. An operating cable
** 5. Door hardware (TDV1 for 2-point latching
or TDV1 and TDV3 for 3-point latching)
When using a circuit breaker, order:
1. A circuit breaker
2. A flange handle (STDA1 or STDA2)
3. A variable depth operating mechanism
** 4. Door hardware (TDV1 for 2-point latching
or TDV1 and TDV3 for 3-point latching)
Siemens I-T-E Max-Flex ™
When using a disconnect switch, order:
1. A basic switch (right-hand)
2. A fuse or no-fuse kit
* 3. FHOHS flange-mounted handle
* 4. Switch operator
* 5. Cable, 36"
** 6. Door hardware (DKR2 for 2-point latching
or DKR3 for 3-point latching)
NOTE: Some I-T-E fixed depth switch operators can be
used. Contact Hubbell/Wiegmann for more information.
When using a circuit breaker, order:
1. A circuit breaker
2. Pressure wire connectors
* 3. FHOH flange-mounted handle (Use
FHOHN for enclosure catalog number
SDN12603812A)
Siemens ITE Max-Flex ™ (cont.)
* 4. A circuit breaker operator mechanism
* 5. An operating cable (standard 36.00" for 125
amp to 600 amp circuit breakers, and
48.00" for 800 amp to 1200 amp circuit
breakers)
** 6. Door hardware (DKR2 for 2-point latching or
DKR2 for 3-point latching)
Schneider Square D ®
When using a Class 9422 disconnect switch, order:
* 1. A disconnect switch with operating
mechanism (Class 9422)
* 2. A handle mechanism (Class 9422 Type A-1)
** 3. A door closing mechanism (Class 9423
Type M4 for 2-point latching, or Class 9423
Type M9 or M4 and Class 9423 Type M3 for
3-point latching)
When using a circuit breaker, order:
1. A circuit breaker (Schneider Square D ® )
* 2. An operating mechanism (Class 9422)
* 3. A handle mechanism (Class 9422 Type A-1)
** 4. A door closing mechanism (Class 9423
Type M4 for 2-point latching, or Class 9423
Type M9 or M4 and Class 9423 Type M3
for 3-point latching)
When using a Class 9422 Type “T” disconnect
switch with a cable mechanism, order:
1. A disconnect switch with operating
mechanism (Class 9422, Type T)
2. A handle mechanism (Class 9422, Type A-1)
3. A cable mechanism (Class 9422, CFT_O)
3-, 5-, or 10-foot
** 4. A door closing mechanism (Class 9423
Type M4 for 2-point latching, or Class 9423
Type M9 or M4 and Class 9423 Type M3
for 3-point latching)
When using a circuit breaker with a cable
mechanism, order:
1. A circuit breaker (Schneider Square D ® )
2. A handle mechanism (Class 9422, Type A-1)
3. A cable mechanism (Class 9422, CFT_O)
3-, 5-, or 10-foot
** 4. A door closing mechanism (Class 9423
Type M4 for 2-point latching, or Class 9423
Type M9 or M4 and Class 9423 Type M3
for 3-point latching)
PLEASE NOTE:
1. Operator adapter plates are not required with
enclosures on page F2-F13.
2. Various other switch accessories and circuit
breaker accessories are available from discon-
nect manufacturers. The information is subject
to change without notice. Please contact
Hubbell/Wiegmann or the disconnect manufac-
turer if there are further questions.
3. The “Space Occupied” tables (pages F16-F22)
are based upon information supplied by dis-
connect manufacturers. Hubbell/Wiegmann
does not assume responsibility for the accuracy
of these dimensions.
4. Check to make certain enclosure size is ade-
quate for disconnect mechanisms and wire
bend space both above line lugs and below
load lugs.
* Items available from disconnect manufacturer as
complete kits.
** Enclosure “A” dimension less than 40.00" (1016mm)
requires a 2-point door closing mechanism.
Enclosures with an “A” dimension of 40.00" or more
require a 3-point latching mechanism.
DISCONNECT ORDERING INFORMATION
When ordering wall-mounted disconnects from the various manufacturers, be sure to order
all of the necessary items. Each company has a different system, so care is required. Order
the following items from the disconnect manufacturer.