Wiegmann WAX-MSSN4 Series - Manual (Page 43)

W M O D S E R I E S E N C L O S U R E S
N E M A 1 2 M O D U L A R F R E E S TA N D I N G D I S C O N N E C T
www.hubbell-wiegmann.com
Data Subject To Change Without Notice
CATALOG NUMBER BODY/DOOR STEEL GAUGE SIZE H X D (SEE DRAWING BELOW)
WMOD7218EPT F o r m e d e n d p l a t e w i t h g a s k e t a n d b o l t s 7 2 . 1 3 x 1 8 . 1 3 ( 1 8 3 2 x 4 6 0 )
WMOD7218FTPT F l a t e n d p l a t e w i t h g a s k e t a n d b o l t s 7 2 . 0 0 x 1 8 . 5 0 ( 1 8 2 9 x 4 7 0 )
WMOD7218GK G a s k e t k i t w i t h g a s k e t a n d b o l t s 7 2 . 0 0 x 1 8 . 0 0 ( 1 8 2 9 x 4 5 7 )
WMOD8418EPT F o r m e d e n d p l a t e w i t h g a s k e t a n d b o l t s 8 4 . 1 3 x 1 8 . 1 3 ( 2 1 3 7 x 4 6 0 )
WMOD8424EPT F o r m e d e n d p l a t e w i t h g a s k e t a n d b o l t s 8 4 . 1 3 x 2 4 . 1 3 ( 2 1 3 7 x 6 1 3 )
WMOD8418FTPT F l a t e n d p l a t e w i t h g a s k e t a n d b o l t s 8 4 . 0 0 x 1 8 . 5 0 ( 2 1 3 4 x 4 7 0 )
WMOD8424FTPT F l a t e n d p l a t e w i t h g a s k e t a n d b o l t s 8 4 . 0 0 x 2 4 . 5 0 ( 2 1 3 4 x 6 2 2 )
WMOD8418GK G a s k e t k i t w i t h g a s k e t a n d b o l t s 8 4 . 0 0 x 1 8 . 0 0 ( 2 1 3 4 x 4 5 7 )
WMOD8424GK G a s k e t k i t w i t h g a s k e t a n d b o l t s 8 4 . 0 0 x 2 4 . 0 0 ( 2 1 3 4 x 6 1 0 )
A C C E S S O R I E S F O R M O D U L A R W M O D S E R I E S N E M A 1 2 F L A N G E - M O U N T E D D I S C O N N E C T S
GASKET GASKET
0.75 2.63
H H H
Gasket Kit Flat End Plate Flanged End Plate
D D D
F43
Space Occupied by Disconnect
Note:
1. See pages F51-F60 for various brands of disconnects for “E”, “F”, “G” and
“WB” dimensions.
2. Disconnects will occupy space on panel shown by dimensions “E”, “F” and “G”. Wiring
space “WB” is available when disconnect is installed in the enclosure.
3. When ordering 24.13 (613mm) deep enclosures, long connecting rods must be
ordered. Long connecting rods are available from disconnect manufacturers.
• ABB Controls flange-operated devices
• Eaton Cutler-Hammer C361 devices
• Eaton Cutler-Hammer C371 operating mechanisms C371E and C371F, order
catalog number C371CS1 connecting rod. For C371G and C371K, order cata-
log number C371CS2 connecting rod.
• General Electric TDA devices, order catalog number TDSR extended length
drive rod
• For Schneider Square D ® 9422 devices, order catalog number 9422-R2 extra
long operating rod(s). Some devices require two rods.
Refer to National Electrical Code ® article 430-10(b) for wiring space required for line
side conductors to be connected to disconnect. Verify your application
to determine if wiring space is adequate.
PANEL
TOP HOLE IN
DISCONNECT
HANDLE
TOP OF DISCONNECT
THIS SPACE IS OCCUPIED
BY DISCONNECT SWITCH
AND FUSE CLIP (IF USED)
OR CIRCUIT BREAKER.
4.06
2.75 G
WB
F
E
C
WB WB
L
End Plates
Used to seal open end(s) of an assembly of modu-
lar enclosures. End plates are available
in two types:
• The 2.63" thick End Plates allow extra wiring
space. The end plate includes a gasket and
mounting bolts.
• The Flat End Plate provides a low profile
cover for the open end of a modular enclosure.
The flat end plate includes gasket and mounting
bolts.
Gasket Kit
Used to join modular enclosures together, includes
gasket and mounting hardware.