Document Outline

• SAFETY INSTRUCTIONS
  • Safety Symbols
  • Safety Guidelines
  • Power cord for the United Kingdom
• GETTING STARTED
  • PEL-3000 Series Introduction
    • Model Line Up
    • Main Features
  • Accessories
    • Package Contents
  • Appearance
    • PEL-3000 Front Panel
      • (PEL-3021/PEL-3041)
      • (PEL-3111)
      • (PEL-3211 Booster Pack)
    • Rear Panel
      • PEL-3021 / PEL-3041
      • (PEL-3111)
      • (PEL-3211 Booster Pack)
    • Display
  • First Time Use Instructions
    • Rack Mount Kits
    • Power Up and Self Test
    • Load Default Settings
    • Setting the Date and Time
    • Load Wiring
    • Load Wire Connections
    • Using the Front Panel Input Terminals
    • Using the Rear Panel Input Terminals
    • Using the Terminal Cover
    • Remote Sense
    • Firmware Update
    • Conventions
    • Help Menu
• OPERATION
  • Basic Operation
    • CC Mode
    • CR Mode
      • CR Units
    • CV Mode
    • CP Mode
    • +CV Mode
    • Turning on the Load
    • Shorting the Load
      • Short Key Configuration
    • Locking the Front Panel Controls
  • Basic Configuration
    • Select the Switching Function
      • Select the Display Units for Dynamic Mode Levels
      • Select the Switching Time Configuration for Dynamic Mode
    • Slew Rate
    • CV Mode Response Speed
    • CC, CR and CP Mode Response Speed
  • Advanced Configuration Settings
    • Soft Start Setting
    • Von Voltage Settings
      • Von Voltage Level
      • Von Voltage Latch
      • Von Voltage Delay
    • Timer Functions
      • Count Time
      • Cut Off Time
    • Auto Load Configuration
    • Load Off (Mode) and Load Off (Range)
  • Step Resolution Configuration
    • Cursor Mode Configuration
    • Step Mode Configuration
  • Protection Settings
    • OCP
    • OPP
    • UVP
    • OVP
    • UnReg
    • Para
  • System Settings
    • Sound Settings
      • Speaker Settings
      • Alarm Tone Settings
    • Display Settings
      • Contrast and Brightness
    • Control Settings
    • Language Settings
  • Go-NoGo
    • Setting the Go-NoGo Limits
    • Running a Go-NoGo Test
  • Program
    • Program Overview
    • Create a Program
    • Create a Program Chain
    • Running a Program or Chain
  • Sequence
    • Normal Sequence Overview
      • Timing Edit Configuration
      • Data Edit Configuration
    • Running a Normal Sequence
    • Fast Sequence Overview
      • Timing Edit Configuration
      • Data Edit Configuration
    • Running a Fast Sequence
  • Save Recall
    • File Structure
    • File Types
    • Saving Files to Internal Memory
    • Saving Files to USB Memory
    • Recalling Files from Internal Memory
    • Recalling Files from USB Memory
    • Recall Memory Safety Setting
    • File Utility
    • Preset
      • Quick Preset Save
      • Quick Preset Recall
    • Default Settings
      • Factory Default Settings
      • User’s Default Setting
• EXTERNAL CONTROL
  • Analog Control
    • J1 Connector Overview
    • External Voltage Control - Overview
      • External Voltage Control – Operation
    • External Resistance Control - Overview
      • External Resistance Control – Operation
    • Turning the Load On using External Control
      • Load On/Off Status
    • External Control of the Range
      • I Range Status
      • External Trigger Signal
    • External Control of the Alarm
      • Alarm Status
    • Short Control
    • Monitor Signal Output
      • Trigger Signal Output
      • Current Monitor Output
  • Parallel Operation
    • Parallel Capacity, PEL-3021, PEL-3041, PEL-3111
    • Parallel Capacity, PEL-3211
    • Connection
    • Configuration
      • Turning the Load On
      • Disable Parallel Mode
• REMOTE CONTROL
  • Interface Configuration
    • Configure to USB Remote Interface
    • Configure GPIB Interface
    • Configure RS232C
    • RS232C/USB Remote Control Function Check
    • Using Realterm to Establish a Remote Connection
    • GPIB Function Check
• FAQ
  • The load voltage indicated on the load module is below expected.
  • The front panel keys are not working.
  • The load won’t turn on.
  • The performance does not match the specification.
• APPENDIX
  • Replacing the Dust Filter
  • Replace the Clock Battery
  • GPIB Installation
  • PEL-3000 Default Settings
  • Frame Control Connector Contacts
  • Operating Mode Description
    • CC Mode
    • CR Mode
    • CP Mode
    • CV Mode
  • Operating Area
  • PEL-3000 Specifications
    • Rating (Master / Slave)
    • Rating (Booster / Slave)
    • CC Mode
    • CR Mode
    • CV Mode
    • CP Mode
    • Slew Rate
    • Meter
    • Dynamic Mode
    • Soft Start
    • Remote Sensing
    • Protection Function
    • Sequence
    • Other
    • Analog External Control
    • Front Panel BNC Connector
  • PEL-3000 Dimensions
    • PEL-3111
    • PEL-3021, PEL-3041
    • PEL-3211
• INDEX