Kinze 3600 Lift and Rotate Planter (70 CM) Rev. 5/14 - Manual (Page 114)

M0249-01 Model 3600
6-10 Rev. 5/14
TM
Lubrication and Maintenance
TM
Lubrication and Maintenance
MOUNTING BOLTS AND HARDWARE
WARNING
Parts separation can result in death, serious injury, and damage
to property and equipment. Check all hardware is tight before
operating planter the first time. Check all hardware again after first
50 hours of operation and beginning of each planting season.
NOTICE
Over-tightening hardware can reduce its shock load capacity and
cause equipment failure.
Hardware used on Kinze planters are Grade 5 (high strength) unless otherwise noted. Grade 5 cap screws are
marked with three radial lines on the head. Hardware must be replaced with equal size, strength, and thread type.
NOTE: Torque EdgeVac fan impeller assembly to
motor shaft ⅝"-18 hex jam nut 50 ft-lb (67.8 N-m).
SPECIAL TORQUE VALUES
Row unit parallel linkage bushing hardware 176 N-m
5/8
" No till coulter spindle hardware 162 N-m
Center section transport tire lug nuts 244 N-m
Wing ground drive tire lug bolts 122 N-m
CYLINDER TORQUE VALUES
½"-20 75-95 N-m
¾"-16 156-169 N-m
⅞ "-14 203-244 N-m
1"-14 373-447 N-m
1⅛"-12 407-508 N-m
1¼"-12 407-508 N-m
TORQUE VALUES CHART - PLATED HARDWARE
Grade 2 (No marks) Grade 5 (3 marks)
Grade 8 (6 marks)
Diameter Coarse Fine Coarse Fine Coarse Fine
¼ " 50 in-lb 56 in-lb 76 in-lb 87 in-lb 9 ft-lb (12 N-m) 10 ft-lb (14 N-m)
5∕16 " 8 ft-lb (11 N-m) 9 ft-lb (12 N-m) 13 ft-lb (18 N-m) 14 ft-lb (19 N-m) 18 ft-lb (24 N-m) 20 ft-lb (27 N-m)
⅜ " 15 ft-lb (20 N-m) 17 ft-lb (23 N-m) 23 ft-lb (31 N-m) 26 ft-lb (35 N-m) 33 ft-lb (45 N-m) 37 ft-lb (50 N-m)
7∕16 " 25 ft-lb (34 N-m) 27 ft-lb (37 N-m) 37 ft-lb (50 N-m) 41 ft-lb (56 N-m) 52 ft-lb (71 N-m) 58 ft-lb (79 N-m)
½ " 35 ft-lb (48 N-m) 40 ft-lb (54 N-m) 57 ft-lb (77 N-m) 64 ft-lb (87 N-m) 80 ft-lb (108 N-m) 90 ft-lb (122 N-m)
9∕16 " 50 ft-lb (68 N-m) 60 ft-lb (81 N-m) 80 ft-lb (108 N-m) 90 ft-lb (122 N-m) 115 ft-lb (156 N-m) 130 ft-lb (176 N-m)
⅝ " 70 ft-lb (95 N-m) 80 ft-lb (108 N-m) 110 ft-lb (149 N-m) 125 ft-lb (169 N-m) 160 ft-lb (217 N-m) 180 ft-lb (244 N-m)
¾ " 130 ft-lb (176 N-m) 145 ft-lb (197 N-m) 200 ft-lb (271 N-m) 220 ft-lb (298 N-m) 280 ft-lb (380 N-m) 315 ft-lb (427 N-m)
⅞ " 125 ft-lb (169 N-m) 140 ft-lb (190 N-m) 320 ft-lb (434 N-m) 350 ft-lb (475 N-m) 450 ft-lb (610 N-m) 500 ft-lb (678 N-m)
1" 190 ft-lb (258 N-m) 205 ft-lb (278 N-m) 480 ft-lb (651 N-m) 530 ft-lb (719 N-m) 675 ft-lb (915 N-m) 750 ft-lb (1017 N-m)
1⅛" 265 ft-lb (359 N-m) 300 ft-lb (407 N-m) 600 ft-lb (814 N-m) 670 ft-lb (908 N-m) 960 ft-lb (1302 N-m) 1075 ft-lb (1458 N-m)
1¼" 375 ft-lb (508 N-m) 415 ft-lb (563 N-m) 840 ft-lb (1139 N-m) 930 ft-lb (1261 N-m) 1360 ft-lb (1844 N-m) 1500 ft-lb (2034 N-m)
1⅜" 490 ft-lb (664 N-m) 560 ft-lb (759 N-m) 1100 ft-lb (1491 N-m) 1250 ft-lb (1695 N-m) 1780 ft-lb (2413 N-m) 2030 ft-lb (2752 N-m)
1½" 650 ft-lb (881 N-m) 730 ft-lb (990 N-m) 1450 ft-lb (1966 N-m) 1650 ft-lb (2237 N-m) 2307 ft-lb (3128 N-m) 2670 ft-lb (3620 N-m)
NOTE: Torque unplated hardware and bolts with lock nuts approximately ⅓ higher than above values. Torque
bolts lubricated prior to installation to 70% of value shown in chart.