Dell PowerVault 770N (Deskside NAS Appliance) - Manual (Page 25)

No PXE-capable device available <F12> pressed
during POST and no
PXE devices are
detected.
Check the configuration settings in the System Setup
program for the NICs (see " Using the System Setup
Program ").
No timer tick interrupt Faulty system board. Replace the system board (see " System Board ").
Not a boot diskette No operating system
on diskette.
Use a bootable diskette.
PCI BIOS failed to install Loose cables to
expansion card(s);
faulty or improperly
installed expansion
card.
Ensure that cables to expansion cards are properly
connected. Ensure that the expansion cards are properly
installed. If the problem persists, replace the faulty expansion
card(s) (see " Expansion Cards ").
Plug & Play Configuration Error
Embedded xxx Error encountered in
initializing PCI
device; faulty system
board.
Install the NVRAM_CLR jumper and reboot the system (see
Figure 5-2 for jumper location). If the problem persists,
ensure that the expansion cards are properly installed. If the
problem still persists, replace the faulty expansion card(s)
(see " Expansion Cards "). If the problem still persists, update
the BIOS firmware. Download the latest firmware from the
Dell Support website at support.dell.com.
Plug & Play Configuration Error
PCI_n Error encountered in
initializing PCI
adapter.
Primary backplane is not
present Faulty or improperly
installed SCSI
backplane board.
Ensure that the SCSI backplane board is properly installed. If
the problem persists, replace the backplane board (see " SCSI
Backplane Board ").
Processor n internal error Faulty
microprocessor;
faulty system board.
Ensure that the microprocessors are properly installed. If the
problem persists, replace the faulty microprocessor(s) (see
" Microprocessors "). If the problem persists, replace the
system board (see " System Board ").
Processor bus parity error
Processor in socket 1 not
installed! No microprocessor
installed in primary
microprocessor
socket.
Install a microprocessor in the primary microprocessor
socket. Also, ensure that a VRM for processor 1 is installed
(see " Microprocessors ").
SCSI cable not present on
connector SCSIA of the primary
backplane SCSI cable is loose,
improperly
connected, or faulty.
Ensure that the SCSI cables are properly installed. If problem
persists, add or replace the cables.
Shutdown failure Shutdown test
failure.
Ensure that the memory modules are properly installed. If
the problem persists, replace the faulty memory module(s)
(see " Memory Modules ").
System backplane error Faulty or improperly
installed SCSI
backplane board.
Ensure that the SCSI backplane board is properly installed. If
the problem persists, replace the backplane board (see " SCSI
Backplane Board ").
System halted! Must power down Wrong password
entered too many
times.
Information only.
Time-of-day clock stopped Faulty battery. Ensure that the system battery is properly installed. If the
problem persists, replace the battery (see " System Battery ").
Time-of-day not set - please
run SETUP program Incorrect Time or
Date settings; faulty
system battery.
Check the Time and Date settings (see " Using the System
Setup Program "). If the problem persists, replace the system
battery (see " System Battery ").
Timer chip counter 2 failed Faulty system board. Replace the system board (see " System Board ").
Unsupported CPU combination Microprocessor(s) is
not supported by the
system.
Update the BIOS firmware. Download the latest firmware
from the Dell Support website at support.dell.com. If the
problem persists, install a supported microprocessor
combination (see " Microprocessors ").
Unsupported CPU stepping
detected
Unsupported DIMM detected in
the RAID DIMM slot! RAID memory
module is not
supported by the
system.
Install a correct version of the RAID memory module (see
" Integrated RAID Controller ").