Document Outline

• OEM Implementation Manual
• Contents
• 1 - Product Overview
  • Introduction
  • Terminology
  • Intended Use
  • Safety and Warnings
  • Measuring Principle
• 2 - Functional Description
  • Introduction
  • Module Integration
  • Power Supply Connections
  • Host Serial Configuration
  • Module Operation
  • Temperature Probes
  • Probe Well and Switch
    • Probe Well
    • Cycle Initiation Switch
    • Probe Well Switch
• 3 - OEM Implementation
  • Introduction
  • EMI/ESD Protection
  • Mechanical Considerations
  • Host Connector Interface
  • Probe Connector
  • Power Requirements
  • Serial Communications Interface
  • Asynchronous Operation
  • Time-out
  • Guidelines
    • Temperature Site Indication
      • Oral Mode
      • Adult Axillary Mode
      • Pediatric Axillary Mode
      • Rectal Mode
    • Monitor Mode
      • Monitor Mode Indication
      • Ready Audible Signal
      • In-Progress Indicator
      • Completion Audible Signal
• 4 - Specifications
• 5 - Verification Testing
  • Introduction
  • Calibration Verification
    • Testing Module Only
    • Procedure
  • Testing the Module and the Probe
• 6 - Regulatory
  • Introduction
  • OEM Responsibility
• 7 - Part Numbers
  • Components from Welch Allyn
  • Components from Other Vendors
• 8 - Communications Protocol
  • Introduction
    • Communications Interface
    • System EEPROM
  • Packet Structure
    • Endian Format
    • Command Block
    • Response Block
    • Type Codes
    • Data Types
      • Character Arrays
      • Simple Data Types
      • Complex Data Types (Structures)
      • Checksum Calculation
  • Commands and Responses
    • (2900) Send Serial Number
      • Command Code (hex)
      • Data
      • Response Data
    • (2913) Send Temperature Method
      • Command Code (hex)
      • Data
      • Response Data
    • (2936) Send Module Software Version
      • Command Code (hex)
      • Data
      • Response Data
      • Notes
    • (2945) Send Thermometer Probe Mode
      • Command Code (hex)
      • Data
      • Response Data
    • (2949) Send Default Thermometer Probe Mode
      • Command Code (hex)
      • Data
      • Response Data
    • (2A06) Save Data to EEPROM
      • Command Code (hex)
      • Data
      • Response Data
    • (2A07) Recall Data from EEPROM
      • Command Code (hex)
      • Data
      • Response Data
    • (2A12) Set Temperature Method
      • Command Code (hex)
      • Data
      • Response Data
      • Notes
    • (2A35) Set Thermometer Probe Mode
      • Command Code (hex)
      • Data
      • Response Data
      • Notes
    • (2A37) Set Default Thermometer Probe Mode
      • Command Code (hex)
      • Data
      • Response Data
      • Notes
    • (3000) Restart Module
      • Command Code (hex)
      • Data
      • Response Data
    • (3101) Send Digital Input Status
      • Command Code (hex)
      • Data
      • Response Data
    • (3109) Erase Event Log
      • Command Code (hex)
      • Data
      • Response Data
    • (3503) Lock Thermometer Probe
      • Command Code (hex)
      • Data
      • Response Data
    • (3604) Set Temperature Probe
      • Command Code (hex)
      • Data
      • Response Data
      • Notes
    • (9401) Send Thermometer Status No Clear
      • Command Code (hex)
      • Data
      • Response Data
      • Notes
    • (9413) Send Mode Pause For Clinical Device
      • Command Code (hex)
      • Data
      • Response Data
    • (9415) Send Default Thermometer Mode
      • Command Code (hex)
      • Data
      • Response Data
    • (9416) Send 690 Event Log
      • Command Code (hex)
      • Data
      • Response Data
    • (941A) Send Programmable Ambient Bias
      • Command Code (hex)
      • Data
      • Response Data
    • (941C) Send Temperature Record
      • Command Code (hex)
      • Data
      • Response Data
      • Note
    • (9433) Set Mode Pause For Clinical Device
      • Command Code (hex)
      • Data
      • Response Data
      • Notes
    • (9434) Set Asynchronous Messages Enabled
      • Command Code (hex)
      • Data
      • Response Data
      • Notes
    • (9435) Set Default Thermometer Mode
      • Command Code (hex)
      • Data
      • Response Data
      • Notes
    • (943A) Set Programmable Ambient Bias
      • Command Code (hex)
      • Data
      • Response Data
    • Data Records
  • Command and Response Strings: Examples
    • Endianness
      • Big-Endian Numbers
      • Little-Endian Numbers
      • IEEE 754 Data Format
      • Converting a String of Bytes to a Floating-Point Number
    • String Examples
      • (2900) Send Serial Number
      • (2936) Send Module Software Version
      • (2A12) Set Temperature Method
      • (3503) Lock Thermometer Probe
      • (9401) Send Thermometer Status No Clear
      • (941C) Send Temperature Record - 19 Data Bytes
      • (941C) Send Temperature Record - 33 Data Bytes
      • (9434) Enable Asynchronous Messages
      • (943A) Set Programmable Ambient Bias
• 9 - Quick Start
  • Introduction
  • Typical Start-up Sequence
• 10 - Programmable Ambient Bias
  • Introduction
  • Host Device Temperature Testing
  • Calculating the Bias
  • Saving Ambient Bias
• 11 - Error Codes and Recovery
• Appendix A - Developer’s Kit
  • Introduction
  • Disclaimer
  • Kit Contents
  • Setup
    • Personal Computer Requirements
    • Software Installation
    • Hardware Installation
  • SureTemp Plus PC Display
    • Operation
      • Normal Mode
      • Monitor Mode
    • Extended Views
      • Temperature Graph
      • Predict Log
      • Communications Log
    • Miscellaneous Functions
      • Communications Port Setup
      • About Screen
      • Comms Log Window
      • Full Display
      • Predict Log
• Appendix B - Cleaning
  • Cleaning the Probe
  • Cleaning the Probe Well