KEYENCE IB Series - Manual (Page 113)

A-5 IB-E
A
ppendix
Receiver error
The receiver is not connected
to the sensor amplifier. Correctly connect the receiver.
"Connecting the Sensor Head" (page 2-9)
The sensor head cable
connector is not connected
correctly. Connect the connector again.
"Attaching the sensor head cable connector
(OP-87060)" (page 2-11)
The receiver is broken. Replace the receiver.
The sensor head cable for the
receiver is broken.
Replace the sensor head cable.
Transmitter laser
error
The laser in the transmitter is
broken.
Replace the transmitter.
Transmitter error
The transmitter is not
connected to the sensor
amplifier.
Correctly connect the transmitter.
"Connecting the Sensor Head" (page 2-9)
The sensor head cable
connector is not connected
correctly. Connect the connector again.
"Attaching the sensor head cable connector
(OP-87060)" (page 2-11)
The transmitter is broken. Replace the transmitter.
The sensor head cable for the
transmitter is broken.
Replace the sensor head cable.
Model mismatch error
The transmitter and receiver
model (measurement range)
do not match.
Use a transmitter and receiver from the same
model (measurement range).
Transmitter
internal error
The transmitter is broken. Replace the transmitter.
Overcurrent error
An overcurrent exceeding the
specifications passed to the
judgment output or check
output.
• Correct the wiring.
"Output Circuit" (page 5-4)
• Check the load and reduce the current to
within the specified range.
• Check that the output wire is not touching
another wire or frame.
EEPROM error
Read/write of the non-volatile
memory (EEPROM) save
data failed. Turn the power on again.
Perform initial reset.
"3-5 Initial Reset (Initialize)" (page 3-12)
The number of writes to the
non-volatile memory
(EEPROM) exceeded
1,000,000 times.
To save the setting values when the power is
turned off, replace the amplifier unit.
If the adjust function or the zero shift function is used frequently, do
not save settings in the non-volatile memory (EEPROM).
"12. Save Zero-Shift State" (page 4-36)
"13. Save Adjust State" (page 4-36)
Error indication Error contents Remedy
T
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
'T*
GO
HOLD CALC CHECK
.#5'4
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
'T*
GO
HOLD CALC CHECK
V
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
'T*
GO
HOLD CALC CHECK
T#P)G
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
'T*
GO
HOLD CALC CHECK
VK06
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
'T*
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
'T%
GO
HOLD CALC CHECK
LASER
BANK 0
1
2
3
HI
LO
R.V. ANALOG
HI SHIFT
ZERO SHIFT
TIMING LO
ALIGNMENT
'T'
GO
HOLD CALC CHECK
Reference