Comtech EF Data SNM-1001 - Manual (Page 77)

Remote Control Operation SNM-1001 Network Control Modem
A–18 Rev. 1
Demod/
Decoder
Config
Program
Status Command:
Response: <add/DCP_'cr'
>add/DCP_'cr'
MOM_xxxxxxx'cr'
BERT_xxxx'cr'
DT_xxxx'cr'
DDT_xxx'cr'
DF_nnn.nnnn'cr'
DR_nnnn_mmm.mmm'cr'
DE_xxx'cr'
DDEC_xxx'cr'
RFL_xxx'cr'
IFL_xxx'cr'
SCF_snnnnn'cr'
SWR_nnnnn'cr'
RDA_xxx'cr'
BC_xxx'cr'
RCP_xxxx'cr'
(Note 1)
BBL_xxx'cr'
IBP_xxx'cr'
IBS_nnnnn'cr'
ADP_xxx'cr'
(Note 2)
SBTR_xxx'cr' (Note 2)
EMS_x'cr' (Note 2)
LAW_y'cr' (Note 2)
ISCL_RX_nnn'cr' (Note 2)
RD_xxx'cr' (Note 2)
SD_xxx'cr' (Note 2)
RR_xxx'cr' (Note 2)
DM_xxx'cr' (Note 2)
ROBR_nnnnn'cr' (Note 3)
RCCL_n'cr' (Note 3)
ROCP_xxxx'cr' (Note 3)
LPC_xxx'cr' (Note 3)
ENSP_nn.n'cr' (Note 4)
MAXT_n.n'cr' (Note 4)
OCT_xxxxx'cr' (Note 5)
TCT_xxxxx'cr' (Note 5)
ISRD_xxx'cr' (Note 5)
ISRR_xxx'cr' (Note 5)
ISDM_xxx'cr' (Note 5)
ISCS_xxx'cr' (Note 5)
ISRT_xxx'cr' (Note 5)
ISST_xxx'cr' (Note 5)
RSDE_xxx'cr'
DSR_xxx'cr''lf']
Modem Operation Mode
BER Threshold
Demodulator Type
Demodulator Decoder Type
Demodulator Frequency
Demodulator Rate
Descrambler Enable (ON/OFF)
Differential Decoder (ON/OFF)
RF Loopback (ON/OFF)
IF Loopback (ON/OFF)
Sweep Center Frequency
Sweep Width Range
Receive BPSK Data Ordering
Buffer Clock (Source)
Receive Clock Phase
Baseband Loop Back
Interface Buffer Programming
Interface Buffer Size
Interface ADPCM Programming
Interface Subscriber/Trunk Emulation
Interface E&M Signal Type
Interface Receive Encoding Law
Interface Service Receive Channel Level
Interface RD Signal
Interface SD Signal
Interface RR Signal
Interface DM Signal
ASYNC Receive Overhead Baud Rate
ASYNC Receive Channel Character Length
ASYNC Receive Overhead Channel Parity
AUPC Local Enable
AUPC E
b /N 0 Target Set Point
AUPC Max. Tracking Rate
ASYNC Overhead Communications Type
Terrestrial Communications Type
ASYNC Interface RD Signal
ASYNC Interface RR Signal
ASYNC Interface DM Signal
ASYNC Interface CS Signal
ASYNC Interface RT Signal
ASYNC Interface ST Signal
Reed-Solomon Decoder
Demodulator Spectrum Rotation
This command is used by the Comtech EFData M:N protection
switch to collect information that is necessary to configure
back-up modems.
Notes:
1. Status only returned when ASYNC board is installed.
2. Status only returned when ADPCM board is installed.
3. Status only returned when ASYNC option is enabled.
4. Status only returned when AUPC option is enabled.
5. Status only returned when ASYNC option is not
enabled.