Flowserve Mark 3 - Manual (Page 12)

USER INSTRUCTIONS MARK 3 High Silicon Iron ENGLISH 71569249 09-04
®
Figure 3-2: Alloy cross-reference chart
Flowserve
Material Code
Designation
Durco Legacy
Codes
ACI
Designation
Equivalent Wrought
Designation
ASTM
Specifications
Material
Group No.
E3020 Ductile iron DCI None None A395, Gr. 60-40-18 1.0
E3033 High chrome iron CR28 None None A532 class 3 Cr
E4027 High chrome iron CR29 None None None Cr
E4028 High chrome iron CR35 None None None Cr
C3009 Carbon steel DS None Carbon steel A216 Gr. WCB 1.1
C3062 Durco CF8 D2 CF8 304 A744, Gr. CF8 2.1
C3069 Durco CF3 D2L CF3 304L A744, Gr. CF3 2.1
C3063 Durco CF8M D4 CF8M 316 A744, Gr. CF8M 2.2
C3067 Durco CF3M D4L CF3M 316L A744, Gr. CF3M 2.2
C3107 Durcomet 100 CD4M CD4MCuN Ferralium
® A995, Gr. CD4MCuN 2.8
C4028 Durimet 20 D20 CN7M Alloy 20 A744, Gr. CN7M 3.17
C4029 Durcomet 5 DV None None None 2.2
K3005 Durco CY40 DINC CY40 Inconel ® 600 A494, Gr. CY40 3.5
K3007 Durco M35 DMM M351 Monel ® 400 A494, Gr. M35-1 3.4
K3008 Nickel DNI CZ100 Nickel 200 A494, Gr. CZ100 3.2
K4007 Chlorimet 2 DC2 N7M Hastelloy ® B A494, Gr. N7M 3.7
K4008 Chlorimet 3 DC3 CW6M Hastelloy
® C A494, Gr. CW6M 3.8
E3041 Duriron
® D None None A518, Gr. 1 No load
E3042 Durichlor 51 ® D51 None None A518, Gr. 2 No load
E4035 Superchlor
® SD51 None None A518, Gr. 2 No load
D4036 Durco DC8 DC8 None None None -
H3004 Titanium Ti None Titanium B367, Gr. C3 Ti
H3005 Titanium-Pd TiP None Titanium-Pd B367, Gr. C8A Ti
H3007 Zirconium Zr None Zirconium B752, Gr. 702C Ti
® Duriron, Durichlor 51 and Superchlor are registered trademarks of Flowserve Corporation.
® Ferralium is a registered trademark of Langley Alloys.
® Hastelloy is a registered trademark of Haynes International, Inc.
® Inconel and Monel are registered trademarks of International Nickel Co. Inc.
3.4.2 Pressure-temperature ratings
The maximum allowable discharge pressure is
6.9 bar (100 psi) from -29 to 176˚C (-20 to 350˚F).
3.4.3 Suction pressure limits
Suction pressure is limited only by the pressure
temperature ratings of the pump. Specific gravity is
limited to 2.0.
3.4.4 Minimum continuous flow
The minimum continuous flow (MCF) is based on a
percentage of the best efficiency point (BEP). Figure
3-3 identifies the MCF.
Figure 3-3: Minimum continuous flow
MCF % of BEP
Pump size 1750/1450
r/min
1180/960
r/min
2K4x3H-13 20% 10%
All other sizes
10% 10%
4 INSTALLATION
High Silicon Iron components
If any of the components of the pump
have been made of High Silicon Iron, the following
precautionary measures should be followed:
• Use hand wrenches rather than impact wrenches
• This equipment should not be subjected to
sudden changes in temperature or pressure
• Avoid striking this equipment with any sharp blows
High Silicon Iron components
Avoid any repair or fabrication welds
on High Silicon Iron components.
4.1 Location
The pump should be located to allow room for
access, ventilation, maintenance, and inspection with
ample headroom for lifting and should be as close as
practicable to the supply of liquid to be pumped.
Refer to the general arrangement drawing for the
pump set.
Page 12 of 48